4-20mA,HART Integral remote H battery powered magnetic flow meter

mag flowmeter is calibrated on ¡À0.2% accuracy liquid test bench, mag flowmeter is calibrationed 5 points. magnetic flow meters are volumetric flow meters which do not have any moving parts. This lack of moving parts reduces the need for maintenance or replacement. mag flowmeter

Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Power supply: 85~250 VAC, 20V~36VDC, 3.6V lithium battery
Size: DN3-DN3000
Sensor material: carbon steel (std), SS304 / SS316 (optional)
Measuring tube: SS304

electromagnetic flowmeter can be used to measure the volume flow of conductive fluid in a closed pipeline. It is widely applied in the flow measurement and control in the fields of chemical and petroleum industry, metallurgy industry, water and wastewater, agriculture and irrigation, paper making, food and beverage industry and pharmaceutical industry, etc.
When the conductive fluid flows through the measuring tube of the sensor, the voltage signal in direct proportion to the average flow velocity of the fluid will be inducted on the electrodes. The signal is amplified and treated by the transmitter to realize various display functions.
Size: 1/8″-120″
Accuracy: ±0.5%
Electrode: SUS316L, Hastelloy B, Hastelloy C
Structure: compact, remote
Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Protection Grade: IP65 std, IP68 optional for remote
Velocity: 0.1~15 m/s
Conductivity: > 5 μS/cm, demineralized water > 20 µS/cm
Power supply: 85~250 VAC, 20V~36VDC, 3.6V lithium battery
Size: DN3-DN3000
Sensor material: carbon steel (std), SS304 / SS316 (optional)
Flange: ANSI, DIN, JIS, etc.

Electromagnetic water meters are often selected because they are obstructionless, cost-effective for aggressive chemicals,slurries,wastewater applications or any dirty liquid which is conductive or water based and provide highly accurate volumetric flow measurement
Standard application products of water treatment industry
Nominal diameter range: DN5~DN2600
Degree of protection can reach IP68
Application suitability – buried or installed underwater
ANSI, DIN, JIS flange are available

Application: Outdoor,underground.Especially
Without power supply places.
Battery Powered: 3.6V lithium battery
Communication Interface:RS485
Wireless Communication:GSM¡¢GPRS¡¢CDMAProtection:IP68

1.Battery powered,three years’ service life, it can connect with GPRS module,achieve remote meter reading;
2.There are 12 months warranty of our products from the date of original delivery, “three guarantees” service (return, replacement, warranty);

Accuracy of QTLD electromagnetic flowmeter can reach 0.2% accuracy and has been calibrated by a third-party laboratory CNAS ISO/IEC 17025:2017, size is DN3-DN3000.
Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Protection Grade: IP65 std, IP68 optional for remote
Velocity: 0.1~15 m/s

Measurement of electromagnetic water meter is independent of fluid density, viscosity, temperature, pressure, and conductivity. Two measuring points inside the meter with no moving parts to eliminate pressure drop, Capable of measuring electric conductive liquid and fluids with low solid contents. liner of magmeter can be PTFE or rubber, our magnetic flow meter have been approved CE-LVD, CE-EMC, ATEX, NSF, tec. it can mag flowmeter is calibrationed 5 points.

Size: 1/8″-120″
Electrode: SUS316L, Hastelloy B, Hastelloy C
Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS

magnetic flow meter is calibrated on ¡À0.2% accuracy liquid test bench, mag flowmeter is calibrationed 5 points. Electromagnetic flowmeters are volumetric flow meters which do not have any moving parts. This lack of moving parts reduces the need for maintenance or replacement. Our mag flow meters have an accuracy over a wide flow range that can often exceed ¡À 0.5% of flow rate. Our MAG flow meters are ideal for liquids.

Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Power supply: 85~250 VAC, 20V~36VDC, 3.6V lithium battery
Size: DN3-DN3000
Sensor material: carbon steel (std), SS304 / SS316 (optional)
Measuring tube: SS304

magentic flow meters are designed for the conductive liquids. Flow in all kinds of conductive liquids can be accurately measured by utilizing the pulsating magnetic fields. These meters are designed with advanced filtering and signal processing circuitry to maximize performance and reliability.
Velocity: 0.1~15 m/s
Conductivity: > 5 ¦ÌS/cm, demineralized water > 20 ¦ÌS/cm
Power supply: 85~250 VAC, 20V~36VDC, 3.6V lithium battery
Sensor material: carbon steel (std), SS304 / SS316 (optional)
Flange: ANSI, DIN, JIS, etc.

Q&T series insert type electromagnetic flowmeter is on the basis of pipeline electromagnetic flowmeter developed a kind of new flow meter.
After adopting the technology of pressure opening and pressure installation, the plug-in electromagnetic flowmeter can be installed without stopping water, and can also be installed on cast iron pipes and cement pipes. The successful development of plug – in electromagnetic flowmeter provides a new method for fluid flow measurement.

Size: 1/8″-120″
Accuracy: ¡À0.5%
Electrode: SUS316L, Hastelloy B, Hastelloy C
Structure: compact, remote
Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Protection Grade: IP65 std, IP68 optional for remote
Velocity: 0.1~15 m/s
Conductivity: > 5 ¦ÌS/cm, demineralized water > 20 ¦ÌS/cm
Power supply: 85~250 VAC, 20V~36VDC, 3.6V lithium battery
Size: DN3-DN3000
Sensor material: carbon steel (std), SS304 / SS316 (optional)
Flange: ANSI, DIN, JIS, etc.
Measuring tube: SS304
Function: High and low alarm, exciting alarm, empty pipe alarm, self-diagnosis

Battery powered electromagnetic flowmeter special for the area without AC220V/DC24V power supply, battery mag flowmeter transfer and monitor data via 4-20mA, pulse, RS485, GPRS. Nominal Pressure: 0.6-1.6MPa (2.5Mpa / 4.0Mpa /6.4Mpa…Max 42Mpa);
Accuracy: ¡À0.5% (Standard), ¡À0.3% or ¡À0.2% (Optional);
Liner: PTFE,Neoprene,Hard Rubber,EPDM,FEP, Polyurethane,PFA;
Electrode: SUS316L,Hastelloy B,Hastelloy C, Titanium,Tantalum,Platinum-iridium;
Structure: Integral,remote,submersible,ex-proof;
Medium Temperature: -20¡æ~+60¡æ (integral type), Remote type(neoprene,Hard rubber,Polyurethane, EPDM) -10¡æ~+80¡æ;
Remote type (PTFE / PFA / FEP)-10¡æ~+160¡æ;
Ambient Temperature: -20¡æ~+60¡æ;

Process connection of insertion magnetic flowmeter is thread ball valve or flange ball valve, it can be install with pressure. insertion electromagnetic flow meter is used to measure the flow of conductive liquids. insertion magmeter, which allows sensor to be installed and retracted from process piping without shutting down the process. size is from DN100-DN3000

Power supply: 85~250 VAC, 20V~36VDC, 3.6V lithium battery
Size: DN3-DN3000
Sensor material: carbon steel (std), SS304 / SS316 (optional)
Flange: ANSI, DIN, JIS, etc.
Measuring tube: SS304
Function: High and low alarm, exciting alarm, empty pipe alarm, self-diagnosis

The Electromagnetic flow meter has the feature of high accuracy and reliability. This magnetic flow sensor is suitable for measuring the flow of liquids, pastes, and slurries in water, chemical, food, pharmaceutical,mining, and agricultural industries etc. The structure of the digital water flow meter has integral type and remote type.

Specifications:
Place of Origin:Henan, China
Brand Name: Q&T
Model Number: QTLD
Accuracy: 0.5%, optional 0.2%
Signal output: 4~20 mA, pulse
Power supply: 220VAC, 24VDC
Body material: Carbon steel
Liner material: PTFE, FEP, PFA, CR, hard rubber, PU, FLS
Electrode material: SUS316L, HC, HB, Ti, Tan, Pt
Connection: Flange, thread, wafer, tri-clamp, union
Protection grade:IP65 / IP 68(optional)

Battery magnetic flowmeter also could measure & display temperature and pressure, humanized human-computer interaction interface, battery mag flow meter enjoy easy operation. Nominal Pressure: 0.6-1.6MPa(2.5Mpa / 4.0Mpa /6.4Mpa…Max 42Mpa);
Accuracy: ¡À0.5% (Standard), ¡À0.3% or ¡À0.2% (Optional);
Liner: PTFE, Neoprene,Hard Rubber,EPDM,FEP, Polyurethane,PFA;
Electrode: SUS316L,Hastelloy B,Hastelloy C, Titanium,Tantalum,Platinum-iridium;
Structure: Integral,remote,submersible,ex-proof;
Process Connection: Flange(Standard),Wafer,Thread,Tri-clamp etc(optional);
Output Signal: 4-20mA / pulse (optional);
Communication: RS485(Optional),HART(Optional),GPRS/GSM(Optional);

Electromagnetic water meter is widely used in the fields of petroleum, chemical industry, metallurgy, textile, pharmacy, food and beverage, paper making, electric power, urban water supply and drainage and environmental protection.
Customized colors for all electromagnetic flow meters
DN50-DN300 wide ranges.
Modbus RS485,pulse output
Drink water, waste water, sea water, beer, juice, chemical and conductive liquids.

Electromagnetic flowmeters have been used for continuous flow measurement in industrial applications for many years. They are ideally suitable for liquids with an electrical conductivity greater than 5 μS/cm. In addition to water and waste water, other contaminated liquids are typical areas of application.
Our product range for flow measurement includes both “Insertion” and “Inline” in different versions. While the magnetic field in “Full Bore” or “Inline” versions extends over the entire pipe cross section, the magnetic field from the immersed sensor in the Insertion version is transmitted only to a part of the medium.
Size: 1/8″-120″
Accuracy: ±0.5%
Electrode: SUS316L, Hastelloy B, Hastelloy C
Structure: compact, remote
Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Protection Grade: IP65 std, IP68 optional for remote
Power supply: 85~250 VAC, 20V~36VDC, 3.6V lithium battery
Size: DN3-DN3000
Sensor material: carbon steel (std), SS304 / SS316 (optional)
Flange: ANSI, DIN, JIS, etc.
Measuring tube: SS304

Battery power electromagnetic flowmeter P68 protection workable under water for few days,Battery power magnetic flowmeter can add external 12-24 V DC power supply with 4-20mA. Size: DN10-DN2000; Nominal Pressure: 0.6-1.6MPa(2.5Mpa / 4.0Mpa /6.4Mpa…Max 42Mpa); Accuracy: ¡À0.5% (Standard), ¡À0.3% or ¡À0.2% (Optional); Structure: Integral,remote,submersible,ex-proof; Medium Temperature: -20¡æ~+60¡æ (integral type), Remote type(neoprene,Hard rubber,Polyurethane, EPDM) :-10¡æ~+80¡æ; Remote type (PTFE / PFA / FEP): -10¡æ~+160¡æ; Protection Class: IP65(Standard),IP68(Optional for remote type); Output Signal: 4-20mA / pulse (optional); Communication: RS485(Optional), HART(Optional), GPRS/GSM (Optional);

QTLD electromagnetic flowmeter is configured with PTFE and SS316L electrodes, with compact or remote type structurer, mag flowmeter is used to measure drinking water or waste water. Structure of electromagnetic flowmeter can be compact or remote with, battery is 85~265 VDC / 85~265VAC / 3.6V lithium battery.
Size: DN3-DN3000
Structure: compact, remote
Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic
Protection Grade: IP65 std, IP68 optional for remote
Power supply: 85~250 VAC, 20V~36VDC, 3.6V lithium battery
Sensor material: carbon steel (std), SS304 / SS316 (optional)

magmeter is mainly used in pharmaceutical industry, in water treatment or in food production: If conductive media such as cooling water are added to a process, standard cable is 10m, max length is 120m, electromagnetic flow meter is mainly used to measure beverage. liner can be PTFE or rubber, our magnetic flow meter have been approved CE-LVD, CE-EMC, ATEX, NSF, tec. it can mag flowmeter is calibrationed 5 points.

Accuracy: ¡À0.5%
Structure: compact, remote
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Protection Grade: IP65 std, IP68 optional for remote
Velocity: 0.1~15 m/s

With simple structure ,the flow meter is of high reliability without lining in the measuring pipe .
The wide range of the nominal bore is suitable for all the pipe size between DN50 and DN300.

Magnetic energy meter is consist of sensor, transmitter and Pt1000 temperature sensor. magnetic heat meter is available for use in pipes ranging in size from DN100 to DN3000, which also can monitor flow and energy of hot water and cold water, standard configuration of flange and sensor shell is carbon steel, SS304 and SS316L are optional.

Size: 1/8″-120″
Accuracy: ¡À0.5%
Repeatability: 0.17%
Electrode: SUS316L, Hastelloy B, Hastelloy C
Structure: compact, remote

Electromagnetic water meter is widely used in iron and steel, electric power, petroleum, chemical industry, coal, metallurgy,Papermaking, water supply and drainage, food, medicine and other industries.

magnetic flowmeter is unaffected by changes in fluid density, viscosity, temperature, pressure and conductivity. There are no obstructing flow parts in the measuring tube, no pressure loss, and lower requirements for straight pipe sections. Unique adaptability to slurry measurement. structurer is compact type and remote type with 10m cable standard and 120m max. hard rubber or Neoprene liner of magnetic flowmeter is configured for drinking water

Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Protection Grade: IP65 std, IP68 optional for remote
Velocity: 0.1~15 m/s
Conductivity: > 5 ¦ÌS/cm, demineralized water > 20 ¦ÌS/cm

Liner of compact liquid flow meter is SS316L standard, HC, Ti, Tan and PT-IR are optional, mag flow meter is mainly used to measure conductive liquid, mag flowmeter has compact and remote structurer. our magnetic flow meter have been approved CE-LVD, CE-EMC, ATEX, NSF, tec. it can mag flowmeter is calibrationed 5 points.
Accuracy: ¡À0.5%
Structure: compact, remote
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Protection Grade: IP65 std, IP68 optional for remote
Velocity: 0.1~15 m/s

Self-diagnosis fault alarm
GSM data infinitely transmitted
LCD display cumulative flow£¬instanta-
neous flow£¬ flow rate,flow percentage,etc.

Battery powered mag flowmeter with Infrared remote control display and
operation, battery flow meter also realize bi-directional measurement,enjoy easy installation. Accuracy: ¡À0.5% (Standard), ¡À0.3% or ¡À0.2% (Optional); Protection Class: IP65(Standard),IP68(Optional for remote type); Process Connection: Flange(Standard),Wafer,Thread,Tri-clamp etc(optional); Output Signal: 4-20mA / pulse (optional); Communication: RS485(Optional),HART(Optional),GPRS/GSM(Optional); Power Supply: Battery powered 3.6V,Battery powered 3.6V +DC24V(Optional); Power Consumption: 0.5W(Standard), 1.5W(with DC24V); Explosion Proof: ATEX

LCD display Partial Filled Pipe Flow Meter digital remote valve control water is composed of converter, flow sensor and level sensor. The user only needs to
enter the diameter of pipe, the non-full pipe flowmeter will automatically calculate the flow rate, and automatically
display the instantaneous flow, total flow, velocity, height, etc. It can measure liquid volume min 10% of full pipe. It is
especially suitable for the needs of municipal rainwater, waste water, sewage discharge and irrigation

Electromagnetic flow meter provides accurate volumetric flow measurement for liquid in closed pipe. Electromagnetic flow meter is often called as: magnetic flow meter,mag flow meter,mag meter,mag-meter,electromagnetic water flow meter,etc. No matter what is called, magnetic flow meter is a kind of high accuracy flow device.Magnetic flow meter has been proved its strength in liquid flow measurement and widely used in the world.
Size: 1/8″-120″
Accuracy: ±0.5%
Electrode: SUS316L, Hastelloy B, Hastelloy C
Structure: compact, remote
Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Protection Grade: IP65 std, IP68 optional for remote
Power supply: 85~250 VAC, 20V~36VDC, 3.6V lithium battery
Sensor material: carbon steel (std), SS304 / SS316 (optional)
Flange: ANSI, DIN, JIS, etc.
Measuring tube: SS304

Q&T series electromagnetic flow meters sensor and transmitter integrity check utilizing fingerprint technology . Verify the installation is correct from day one and Receive timed notifications. Protect your investment in Q&T flowmetering. Q&T Series nominal diameter DN3-DN3000. There are many options for sensor liner and electrode materials.

Size: 1/8″-120″
Accuracy: ¡À0.5%
Electrode: SUS316L, Hastelloy B, Hastelloy C
Structure: compact, remote
Liner: PTFE, PFA, Polyurethane, Neoprene, Hard Rubber, Ceramic
Output Signal: 4~20 mA, Pulse
Communication: RS485, HART, PROFIBUS
Protection Grade: IP65 std, IP68 optional for remote
Velocity: 0.1~15 m/s
Conductivity: > 5 ¦ÌS/cm, demineralized water > 20 ¦ÌS/cm
Power supply: 85~250 VAC, 20V~36VDC, 3.6V lithium battery
Size: DN3-DN3000
Sensor material: carbon steel (std), SS304 / SS316 (optional)
Flange: ANSI, DIN, JIS, etc.
Measuring tube: SS304
Function: High and low alarm, exciting alarm, empty pipe alarm, self-diagnosis

3.6V battery powered magnetic flow meter service life with 5 years, 3.6V battery powered mag flow meter fulfills the special customer demands to water application as well as irrigation. Nominal Pressure: 0.6-1.6MPa(2.5Mpa / 4.0Mpa /6.4Mpa…Max 42Mpa); Accuracy: ¡À0.5% (Standard), ¡À0.3% or ¡À0.2% (Optional); Measuring Range: Max 15m/s; Conductivity: >5us/cm; Protection Class: IP65(Standard),IP68(Optional for remote type); Output Signal: 4-20mA / pulse (optional); Communication: RS485(Optional),HART(Optional),GPRS/GSM(Optional); Power Supply: Battery powered 3.6V,Battery powered 3.6V +DC24V(Optional);