Factory Open Channel Water Meters Ultrasonic open channel meter for sewage sludge

OEM DN15-DN6000 China Wall Mounted Ultrasonic Water Flowmeter is a portable liquid flow measurement device with a sensor. This 2-inch clamp-On Ultrasonic Flow Meterutilizes proven transit-time ultrasonic measurement technology for superior accuracy and ease of installation and installation. This easy-to-use flowmeter comes in a rugged, waterproof carrying case for easy transport of the display, sensor, and cables between measurement locations. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring single clean liquids Power supply: 24VDC/85VAC-2265AC Storage: SD card optional Heat meter optional

Transit Time Ultrasonic can work alone without a LCD andKeypad module,the module can be used alone as a flow meter.Users caneven integrate a number of the modules into a multi-channel flow meter thatcan measures up to several dozen of different pipes or a flow meter that has higher accuracy by measures the same pipe with all the channels.
Pipe material: Steel, stainless steel, cast iron, copper, cement, PVC, aluminum, glass fiber reinforced plastics, pipes with liner also work
Pipe diameter: 15~6000mm
StraightpipeInstallation condition: upstream10D, downstream 5D, 30D from the pump
Medium Liquid type: Single liquid that could transmit sound wave,
Sewage with small particle content;
Chemicals (alcohol, etc. ) Plant effluent; Beverage;
Ultra-pure liquids, etc.
Temperature: -30~160¡ãC
Turbidity: Not more than 10000ppm, few bubble
Flow rate: 0~¡À7m/s

QT621 handheld type ultrasonic water flow meter adopt transit-time principle.Portable ultrasonic flow meter support precise bidirectional and highly dynamic flow measurement with the non-invasive clamp-on technology. Portable ultrasonic flow meter mainly applies for measuring the flow of homogeneous medium fluid .

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

Q&T clamp on small size flow meter involves sending and receiving ultrasonic pulses from clamp on sensors and examining the time difference in the signal. QT811 small pipe ultrasonic clamp on meters are uitable for various liquids and compatible with various pipeline materials and sizes.

Pipe Size:?DN15-DN40mm (1/2¡±~1 1/2¡±)
Flow Range:¡À0.1m/s ~¡À5m/s
Temperature: 0~75¡æ (standard)
Output: 4-20mA, OCT Pulse, RS485
Accuracy:?¡À1% of measured value
Power Supply: DC10-24V

Non-contact Open Channel flow meter measures level, flow rate and total volume of water flowing through weirs, flumes and channels. The flow meters use a non-contact level sensor. Application field£º
1. Water and sewage treatment£ºpump room, collection well, biochemical reaction
tank, sedimentation tank.
2. Electricity, mines£ºmortar pool, coal slurry pool, butter storage tank, stockyard
or some mobile equipment control, etc.
3. Food industry£ºwineries, granaries, storage tanks for food materials, etc.

Specifications:
Display: Backlight?LCD
The?maximum?of Accumulative Flow: 9999999.9?m3/h
Resolution: 1mm
Analogue?Output: 4-20mA
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS RTU
Ambient?Temperature: -40 ~70 Degree C
Power?Supply: DC24V, AC 220V£»Optional?DC12V

Protable Ultrasonic Water Flowmeter Price,Ultrasonic Flow Meter is a portable liquid flow measurement device with a sensor. Protable Ultrasonic Water Flowmeter Price,Ultrasonic Flow Meter adopt transit-time ultrasonic measurement technology for superior accuracy and ease of installation and installation. This easy-to-use flowmeter comes in a rugged, waterproof carrying case for easy transport of the display, sensor, and cables between measurement locations. High accuracy +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

Portable Hand Held Ultrasonic Flow Meter are widely used in tap water, heating, water conservancy, metallurgy, chemical industry, machinery, energy and other industries. Portable Hand Held Ultrasonic Flow Meter can be used for production monitoring, flow verification, temporary detection, flow inspection, water meter balance debugging, heat network balance debugging, and energy-saving monitoring. Measuring accuracy: +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

Ultrasonic flowmeters use sound waves to determine the velocity of a fluid flowing in a pipe.
Inline type ultrasonic flow meter can be OEM,such as Body color,Transmitter color,Channle number,Logo display etc.
Q&T brand ultrasonic flow meter is one kind of economy type flow meter for liquid,multi channle inline ultrasonic flow meter can reach 0.5% accuracy

DN50-DN700 River water handheld ultrasonic flowmeter sensor Installation process is very simple, all Chinese human-machine interface, more easy to operate. Particularly suitable flow balance testing and flow monitoring: drinking water, river water, sea water, cooling water, hot water, industrial waste water, lubricating oil, diesel oil, fuel oil, chemical liquids. Accuracy: +/-1.0% of FS Wide range: DN300mm-DN6000mm Measuring clean liquids Built-in rechargeable battery 3.6V 2000 lines storage Communication: RS232

Handheld ultrasonic flow meter for water medium is a portable liquid flow measurement device with a sensor. Handheld ultrasonic flow meter for water medium proven transit-time ultrasonic measurement technology for superior accuracy and ease of installation and installation. This easy-to-use flowmeter comes in a rugged, waterproof carrying case for easy transport of the display, sensor, and cables between measurement locations. High accuracy +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

Digital Ultrasonic flowmeter DN15 to DN6000mm Ultrasonic Flow meter is a high precision no-cut tube measurement method. This special design includes matching sensors for ease of use and is ideal for installation in existing systems Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring single clean liquids Power supply: 24VDC/85VAC-2265AC Storage: SD card optional Heat meter optional

This ultrasonic water flow meter can directly display the instantaneous and cumulative flow. This Non-contact ultrasonic flow meter is based on the flow rate-water level calculation method, and adopts an advanced flow rate measuring instrument and water level measuring instrument to ensure a new intelligent flow system.

Specifications:
Sensor?Level?Range: 0-4.0m; other?level?range?also?available
Blind?zone: 0.20m
Temperature?Compensation: Integral?in?probe
Pressure?Rating: 0.2MPa
Beam?Angle: 8*?(3db)
Cable?Length: 10m?standard?(can?be?extended?to?1000m)
Sensor?Material: ABS,?PVC?or?PTFE?(optional)
Sensor?Protection Class: IP68
Output: 4-20mA, Relays, RS485

Not affected by water quality, the ultrasonic open channel flowmeter can be equipped with a communication interface, which is easy to connect with SCADA systems to achieve industrial remote monitoring and control.

Specifications:
Sensor?Level?Range: 0-4.0m; other?level?range?also?available
Blind?zone: 0.20m
Temperature?Compensation: Integral?in?probe
Pressure?Rating: 0.2MPa
Beam?Angle: 8*?(3db)
Cable?Length: 10m?standard?(can?be?extended?to?1000m)
Sensor?Material: ABS,?PVC?or?PTFE?(optional)
Sensor?Protection Class: IP68

According to market request,the power supply can 24VDC or 220VAC or solar powered;Current the solar powered ultrasonic flow meter is more popular,beacuse solar powered meets international requirements, energy saving and environmental protection.

PLCM series ultrasonic open channel flow meter is a low cost choice. It is a hot sell product for river channel measuring. The product supports weirs or notches of different standards in various countries and can be widely used for measurement or monitoring of total water drainage.
Display: Backlight LCD
The maximum of Accumulative Flow: 9999999.9 m3/h
Accuracy of Change in Level: 1mm or 0.2% of full span (whichever is greater)
Resolution: 1mm
Analogue Output: 4-20mA, corresponding to instantaneous flow
Relays Output: Standard 2 relay outputs(Optional up to 6 relays)
Serial Communication: RS485, MODBUS -RTU standard protocol
Ambient Temperature: -40 ~70 Degree C
Power Supply: DC24V (+5%) 0.2A; AC220V (+20%) 0.1A ;Optional DC12V

Ultrasonic Flow meter for applications in clean water and in low conductivity media. Operating principle based on transit time measurement.
Pipe material:Steel,Stainless steel,Cast iron,PVC,Cement pipe and allow pipe with lining
High Isolation voltage,Strong anti-interference,Suppress voltage noise,Good isolation performance
Inline ultrasonic flow meter collect temperature signal and accuracy reach 0.001¡æ
When using inline ultrasonic flow meter to measure,allowing pipe with liner

4-20mA Output Ultrasonic Water Flow Meter BTU meter is designed to work with clamp-on transducers to enable the flow of a liquid within a closed pipe to be measured accurately without needing to insert any mechanical parts through the pipe wall or protrude into the flow system.

The portable ultrasonic flowmeter can be used with various types of detectors applicable for small to large diameter pipe (0.5″” to 236″” / 15mm to 6000mm) and low to high temperature (?30 to +160¡ãC).
This Ultrasonic liquid flow meter is designed for 12 hours of continuous operation with a built-in battery ,allows flow, velocity and total data to be stored. Though RS232 to connect with a PC to facilitate configuring the storage as well as saving and reading data files.
Sensor: Clamp-on/External
Principle: transmit time
Size: DN15mm-DN6000mm Measuring medium: Liquid
3.6V Battery-powered

QT621 ultrasonic flow meter is a type of portable flow meter, main advantage is that the meter can be easily moved and installed in different pipes and convenient to carry site to site. Portable ultrasonic flow meter adopt the innovative design includes matched precision transducers
and signal processing circuitry to accurately measure the flow of most liquids over a wide range of velocities.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

For the Solar Power Open Channel Water Meters, the level sensor is mounted on the top of the flume, and ultrasonic wave is transmitted by the probe to the surface of the monitored material. Instead of using mass or volumetric data to determine the rate of flow of a substance, open channel flow meters monitor the relationship between the depth of the liquid and the flow rate.Open Channel Flow Meter can be used for continuous measurement of municipal rainwater, wastewater, sewage discharge and irrigation water pipelines.

Specifications:
Sensor?Level?Range: 0-4.0m; other?level?range?also?available
Blind?zone: 0.20m
Temperature?Compensation: Integral?in?probe
Pressure?Rating: 0.2MPa
Beam?Angle: 8*?(3db)
Cable?Length: 10m?standard?(can?be?extended?to?1000m)
Sensor?Material: ABS,?PVC?or?PTFE?(optional)
Sensor?Protection Class: IP68

2 inch ultrasonic water flow meter ultrasonic flowmeter is a low-cost portable device with a sensor for non-invasive liquid flow measurement. This 2 inch flow meter ultrasonic flowmeter utilizes proven time difference ultrasonic measurement technology for excellent accuracy and ease of setup and installation.
This easy-to-use flowmeter comes with a sturdy, waterproof carrying case that allows easy transport of the display, sensor, and cables between measurement locations.
Accuracy: +/-1.0% of FS
Wide range: DN15mm-DN6000mm
Measuring single clean liquids
Power supply: 24VDC/85VAC-2265AC
Storage: SD card optional
Heat meter optional

Handheld Ultrasonic Water Flowmeter Clamp on Flow meter is easy and accurate flow measurement without interrupting the process, Clamp-on type transducer easily mountable on existing pipes, non-invasive type.Suitable for most of applications. Measuring accuracy: +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Built-in rechargeable battery 3.6V Communication: RS232

Industrial ultrasonic flow meter output for water ultrasonic flow meter pvc pipe heat meter is a ideal for liquids such as chemical,visous liquids, and sea water. The non-intrusive, clamp-on ultrasonic flow meter fits pipes between 1/2″ to 48″ internal diameter. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Medium: clean liquids,pure water Built-in rechargeable battery 3.6V Measurment unit: Meter, Feet,Cubic Meter.

QT811 clamp on type ultrasonic flow meters support quickly verify the reading of another meter and to data log flow system values over an extended time period.
Specially external clamp design, QT811 clamp on ultrasonic energy BTU meter are mounted externally on the surface of the pipe and which generate pulses that pass through the pipe wall.

Pipe Size:?DN15-DN40mm (1/2¡±~1 1/2¡±)
Flow Range:¡À0.1m/s ~¡À5m/s
Temperature: 0~75¡æ (standard)
Output: 4-20mA, OCT Pulse, RS485
Accuracy:?¡À1% of measured value
Power Supply: DC10-24V

QT621 portable type ultrasonic clamp on flow meters use clamp-on transducers that are mounted externally on the surface of the pipe and which generate pulses that pass through the pipe wall.
Portable ultrasonic flow meters are widely applicated from simple water flow measurements to energy flow monitoring and automated process control.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

This liquid flow meter for industrial is easy and accurate flow measurement without interrupting the process, Clamp-on type transducer easily mountable on existing pipes, non-invasive type.Suitable for most of applications. Measuring accuracy: +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Built-in rechargeable battery 3.6V Communication: RS232

China wall mounted Clamp on pipe ultrasonic water flow meter price provide you with an accurate, easy-to-install flow meter. wall mount flow sensor feature quick, easy clamp-on sensor installation, configuration, and a user-programmable menu-driven interface for easy commissioning in the field. China wall mounted Clamp on pipe ultrasonic water flow meter price use a special algorithm and technology to ensure highly accurate flow measurement. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring single clean liquids Power supply: 24VDC/85VAC-2265AC Storage: SD card optional Heat meter optional

RS232 3.6V Lithium Battery Digital Water Handheld Ultrasonic Flow Meter is a non-contact instrument, which can measure the flow of medium with large diameter and can also be used for the measurement of medium that is not easy to contact and observe. Digital Water Handheld Ultrasonic Flow Meter measurement accuracy is very high, and it is hardly disturbed by various parameters of the measured medium.
Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Medium: clean liquids,pure water Built-in rechargeable battery 3.6V Communication: RS232

Q&T PLCM Open Channel flow meter is Wall mounted converter ultrasonic flow meter for sewage water Open Channel Flow Meter, The cable length between probe and host up to 1000m; This PLCM ultrasonic flow meters are perfect for wastewater applications.
The probe with leak-proof structure and IP68 protect grade.
Display: Backlight LCD
The maximum of Accumulative Flow: 9999999.9 m3/h
Accuracy of Change in Level: 1mm or 0.2% of full span (whichever is greater)
Resolution: 1mm
Analogue Output: 4-20mA, corresponding to instantaneous flow
Relays Output: Standard 2 relay outputs(Optional up to 6 relays)
Serial Communication: RS485, MODBUS -RTU standard protocol
Ambient Temperature: -40 ~70 Degree C
Power Supply: DC24V (+5%) 0.2A; AC220V (+20%) 0.1A ;Optional DC12V

China wall-mounted ultrasonic water flow meter price is an ultrasonic flowmeter used to measure the flow rate of liquids in closed pipes. The transducer is clamp-on type, which will provide the benefits of contamination-free operation and ease of installation. The transit time flowmeter includes two transducers, which act as ultrasonic transmitters and receivers. The transducer can be installed in a v-type method, where the sound travels through the pipe twice, a w-type method, where the sound travels through the pipe four times. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485