hydraulic oil metal tube float rotameter flowmeter

A rotameter is an industrial flowmeter used to measure the flowrate of liquids and gases. The rotameter consists of a tube and float. The float response to flowrate changes is linear, and a 10-to-1 flow range or turndown is standard. In the case of OMEGA? laboratory rotameters, far greater flexability is possible through the use of correlation equations. The rotameter is popular because it has a linear scale, a relatively long measurement range, and low pressure drop. It is simple to install and maintain.
Range ratio: 10:1(Special type 20:1).
Accuracy class: 2.5(Special type 1.5% or 1.0%).
Working pressure: DN15~DN50 PN16 (Special type 2.5MPa).
Medium temperature: Normalized type -80¡æ~+220¡æ.
Ambient temperature: -40¡æ~+120¡æ(Remote display without LCD¡Ü85¡æ).

large range ratio (10:1), convenient installation and maintenance, it is
widely used in flow measurement and process control of small flow rate,
low flow rate and various harsh medium conditions in various industries
and harsh environments
Range ratio:10:1(Special type 20:1)
Accuracy class:2.5(Special type 1.5% or 1.0%)
Working pressure:?DN15~DN50 PN16MPa (Special type 25MPa).
DN80~DN150 PN10MPa (Special type 16MPa).
Pressure rating of jacket 1.6MPa.
Output:4~20mA/?HART?/RS485?/Alarm?/Pulse
Connection mode:Flange Thread Tri-clamp

Variable area flow meter Series are used for measure instantaneous and accumulated flow rate of liquid, gas and steam in closed pipelines. It is suitable for metering flow value on site or electronic remote. The measuring principle is based on the hydrodynamic effects,This makes float moving from bottom to top in vertical Pipe. As the displacement of float is in related to flow rate, which can be read from the indicator by means of the magnetic drive system in non-contact form . Also, flowmeters output electrical signal (4-20)mA / hart communication protocol with high / low limit Warning switches/integrating flow PCB broad can be configured.
Range ratio: 10:1(Special type 20:1).
Accuracy class: 2.5(Special type 1.5% or 1.0%).
Working pressure: DN15~DN50 PN16 (Special type 2.5MPa).
Medium temperature: Normalized type -80¡æ~+220¡æ.
Ambient temperature: -40¡æ~+120¡æ(Remote display without LCD¡Ü85¡æ).

The float of the metal tube float flowmeter moves the float upward with the change of the flow rate in the measuring tube, and the buoyancy of the float and the gravity of the float reach a balance at a certain position. At this time, the flow annulus area between the float and the orifice plate (or cone tube) remains constant. The area of the annular gap is proportional to the rising height of the float, that is, the float is in the measuring tube, the rising position represents the flow rate, and the changing position of the float is transmitted by the internal magnet to the external indicator, so that the indicator can correctly indicate the flow at this time. value. This makes the indicator housing not in direct contact with the measuring tube, so even if a limit switch or transmitter is installed, the instrument can be used under high temperature and high pressure working conditions

The metal tube rotameter adopts 304/316 stainless steel structure, which can be used to measure the flow of liquid, gas, and steam. It is especially suitable for low measurement of low flow rate, micro flow range, high temperature, high ressure, corrosive, conductive or non-conductive medium.
Range ratio:10:1(Special type 20:1)
Accuracy class:2.5(Special type 1.5% or 1.0%)
Working pressure:?DN15~DN50 PN16MPa (Special type 25MPa).
DN80~DN150 PN10MPa (Special type 16MPa).?Pressure rating of jacket 1.6MPa.
Output:4~20mA/?HART?/RS485?/Alarm?/Pulse
Connection mode:Flange Thread Tri-clamp

Metal tube rotameter is all metal structure design, short stroke, easy to install. Metal tube rotameter HART intelligent indicator adopts foreign signal acquisition and processing chip, modular design, without any transmission mechanism transmitter, no magnetic lag; metal tube rotameter and rotameter have data recovery, data backup, failure Electrical protection and error self-diagnosis function, parameter configuration and on-site adjustment can be carried out through the HART communication hand-held communicator. HF metal tube rotameter and rotameter are sturdy, simple, and have a long service life. They are used in the measurement and process control of liquid, gas, and steam media in petroleum, chemical, metallurgy, electric power, medicine, food, paper and other industries.

Metal rotameter is a variable area flow measurement instrument commonly used in industrial automation process control. It has the characteristics of small size, large detection range and convenient use. It can be used to measure the flow of liquid, gas and steam. It is especially suitable for medium flow measurement with low flow rate and small flow.

Metal rotameter according to the explosion-proof requirements, they
can be divided into three types: common type, intrinsically safe type and isolated explosion-proof type.
Range ratio:10:1(Special type 20:1)
Accuracy class:2.5(Special type 1.5% or 1.0%)
Working pressure:?DN15~DN50 PN16MPa (Special type 25MPa).
DN80~DN150 PN10MPa (Special type 16MPa).
Pressure rating of jacket 1.6MPa.
Output:4~20mA/?HART?/RS485?/Alarm?/Pulse
Connection mode:Flange Thread Tri-clamp

The metal rotor flowmeter has a simple structure, no moving parts, and is not easy to be worn by the fluid. The working performance is stable, reliable and has a long service life; Low loss, ideal for high-precision flow measurement. It is a kind of flow measuring instrument commonly used in industrial automation process control. It has the characteristics of small pressure loss, large detection range (range ratio 10:1), and easy to use. It can be used to measure the flow of liquid, gas and steam. It is especially suitable for Low flow rate and small flow medium flow measurement.

metal rotameter mainly used in liquid, acid ,or gas flow measurement and automatic control system in the oil, chemical, pharmaceutical, food and other industries.
Range ratio:10:1(Special type 20:1)
Accuracy class:2.5(Special type 1.5% or 1.0%)
Working pressure:?DN15~DN50 PN16MPa (Special type 25MPa).
DN80~DN150 PN10MPa (Special type 16MPa).
Pressure rating of jacket 1.6MPa.
Output:4~20mA/?HART?/RS485?/Alarm?/Pulse
Connection mode:Flange Thread Tri-clamp

The metal tube high temperature rotameter flowmeter has the advantage of small volume and convenient operation.It is a kind of variable area flow quantity measuring instrument.Ithas various such as field indication type,intelligent remote transmission type,corrosionresistan type,clamped type and damping type.lt can measure the flow of the media with small flow velocity and small flow quantiy.
Range ratio:10:1(Special type 20:1)
Accuracy class:2.5(Special type 1.5% or 1.0%)
Working pressure:?DN15~DN50 PN16MPa (Special type 25MPa).
DN80~DN150 PN10MPa (Special type 16MPa).?Pressure rating of jacket 1.6MPa.
Output:4~20mA/?HART?/RS485?/Alarm?/Pulse
Connection mode:Flange Thread Tri-clamp

Rotameter adopts the international advanced Honeywell non-contact magnetic sensor for detecting the change of magnetic field angle, and is equipped with Motorola micro-processing system, which can realize the functions of liquid crystal indication, accumulation, remote transmission (4 ~ 20mA), pulse output, upper and lower limit alarm output, etc.
Range ratio:10:1(Special type 20:1)
Accuracy class:2.5(Special type 1.5% or 1.0%)
Working pressure:?DN15~DN50 PN16MPa (Special type 25MPa).
DN80~DN150 PN10MPa (Special type 16MPa).?Pressure rating of jacket 1.6MPa.
Output:4~20mA/?HART?/RS485?/Alarm?/Pulse
Connection mode:Flange Thread Tri-clamp

Q&T series of metal tube rotameter intelligent transmitter based on MCU microprocessor, The use of magnetic sensor, The digital filter,Digital signal processing technology such as software correction,To detect the changes in the magnetic field,And through the liquid crystal display screen,Provide good man-machine interface, Can output 4-20mA current signal, A variety of signal alarm etc..
Range ratio:10:1(Special type 20:1)
Accuracy class:2.5(Special type 1.5% or 1.0%)
Working pressure:?DN15~DN50 PN16MPa (Special type 25MPa).
DN80~DN150 PN10MPa (Special type 16MPa).?Pressure rating of jacket 1.6MPa.
Output:4~20mA/?HART?/RS485?/Alarm?/Pulse
Connection mode:Flange Thread Tri-clamp

metal tube rotameter is suitable for small flow ranges with high accuracy. Its display can be a mechanical pointer or LCD digital
display. If digital metal tube rotameter, it can send 4-20ma output and have RS 485. It can also be equipped with a limit switch and alarm.
BCST metal tube rotameter consists of a tapered tube, inner float, and display part. Each part is made by ourselves, from electric board to
float, so the delivery time is fast, there is enough raw material in stock. Usually, it is 3-4 working days for standard products.

metal tube rotameter/ variable area flow meter is suitable for aggressive fluids measurement. It is a traditional and classic flow metering technology which is used in many applications in industry for monitoring the medium flow rate. This rugged flow meter can be used to measure caustic soda, hydrofluoric acid, sulfuric acid and so on.
Range ratio: 10:1(Special type 20:1).
Accuracy class: 2.5(Special type 1.5% or 1.0%).
Working pressure: DN15~DN50 PN16 (Special type 2.5MPa).
Medium temperature: Normalized type -80¡æ~+220¡æ.
Ambient temperature: -40¡æ~+120¡æ(Remote display without LCD¡Ü85¡æ).

The metal rotor flowmeter has the characteristics of simple structure, reliable operation, wide application range, accurate measurement and convenient installation. Divided into field indication type and electric remote transmission type, common type flow sensor, instrument material is (1Cr18Ni9Ti), anti-corrosion type is (1Cr18Ni9Ti) lined with PTEF. If the medium measured by the metal rotameter contains ferromagnetic particles, a magnetic filter should be installed at the inlet of the flowmeter. Its material should be the same as the corresponding flowmeter.

liquid and gas metal tube float rotameter consists of measuring pipe, float, indicator and process connection components with the characteristics of small size, wide measuring range, easy installation. In the industry area, it is widely used to measure flow of gas, liquid, and steam, especially suitable for mediums with low current velocity and low flow rate
Range ratio:10:1(Special type 20:1)
Accuracy class:2.5(Special type 1.5% or 1.0%)
Working pressure:?DN15~DN50 PN16MPa (Special type 25MPa).
DN80~DN150 PN10MPa (Special type 16MPa).
Pressure rating of jacket 1.6MPa.
Output:4~20mA/?HART?/RS485?/Alarm?/Pulse
Connection mode:Flange Thread Tri-clamp

It operates on the principle of variable area; the fluid in the metal tube raised a float in the taper tube increasing the area of passage of fluid. The float moves up in proportion to the rate of flow of fluid and get stabilized when the weight of the float is balanced by the upward hydraulic force. By a magnetic coupling the inner float movement through a series of linkages and counter weight. The tube and the float combination determine the flow rate. The inner float magnetic field is detected by the high sensitive magnetic field detection sensor, enable us to show the digital readout.As such this flow meter does not require any electrical connection, since it operates on battery. It has an inbuilt two wire transmitter provide 24 VDC and take 4 – 20 mA signal.

Metal tube rotameter is a kind of variable area flow measuring instrument commonly used in automatic process control of I industry. It has the characteristics of small size, large detection range and convenient use. It can be used to measure the flow of liquids, gases and steam. It is especially suitable for medium flow measurement with low flow rate and small flow. Metal tube rotameter has local display type and intelligent remote transmission type, supports a variety of output protocols, provides users with a very broad choice space, various excellent performance and reliability of metal tube rotameter, and better performance. Cost-effective, widely favored by petrochemical, steel, metallurgical light industry, food, pharmaceutical, water treatment and other industries.

The float of the metal rotameter is in the measuring tube. With the change of flow, the float moves up, and the buoyancy of the float and the gravity of the float reach a balance at a certain position. At this time, the flow annulus area between the float and the orifice plate (or cone tube) remains constant. The area of the annular gap is proportional to the rising height of the float, that is, the rising position of the float in the measuring tube represents the flow rate, and the position of the changing float is transmitted by the internal magnet to the external indicator, so that the indicator can correctly indicate the flow value at this time. . This makes the indicator housing not in direct contact with the measuring tube, so even if a limit switch or transmitter is installed, the instrument can be used under high temperature and high pressure working conditions. It is a variable area flow measuring instrument commonly used in industrial automation process control. It has the characteristics of small size, large detection range and convenient use. It can be used to measure the flow of liquid, gas and steam, especially suitable for medium flow measurement with low flow rate and small flow.

Tube Rotameter is a variable area flow meter Model KIT series is suitable for gas and liquid flow measurement even under high pressure and high temperature. Standard flow tube is in SS 316 and for corrosive applications the metal tube, orifice and float can be lined with PTFE. KIT series Metal Tube Rotameter comes with optional limit switches and 4-20ma output
Range ratio: 10:1(Special type 20:1).
Accuracy class: 2.5(Special type 1.5% or 1.0%).
Working pressure: DN15~DN50 PN16 (Special type 2.5MPa).
Medium temperature: Normalized type -80¡æ~+220¡æ.
Ambient temperature: -40¡æ~+120¡æ(Remote display without LCD¡Ü85¡æ).

The remote type metal tube rotameter can be used in flow measurement and process control in complex, harsh environments and various medium conditions, and is suitable for measuring liquids and gases. Especially suitable for small diameter and low flow rate medium flow measurement; widely used in: chemical industry, power generation, food, water treatment, etc. In the process of flow measurement in complex, harsh environmental conditions, and various medium conditions.

The metal tube rotameter is a variable area flow meter based on the float position measurement, which is especially suitable for the measurement of gas and liquid flow with low flow rate and small flow. The metal tube float adopts an all-metal structure and a Modular concept design. It has the characteristics of small volume, small pressure loss, large range ratio, and convenient installation and maintenance. Therefore, it is widely used in complex and harsh environments in various industries. Flow measurement and process control for harsh media conditions.

The metal tube float flow meter adopts the variable area measurement principle and is suitable for measuring the flow of various liquids and gases. The flowmeter adopts an all-metal structure, and includes on-site indication type, data remote transmission type, corrosion-resistant type, high temperature and high pressure type, jacket type, and explosion-proof type. It has 0-10mA, 4-20mA standard analog signal output and on-site indication, cumulative digital communication, on-site modification of measurement parameters, different power supply methods, and can be equipped with magnetic filters and special specifications. It is widely used in the measurement and control of various media in complex and harsh environments such as petroleum, chemical, power generation, pharmaceuticals, food, and water treatment.

Metal tube rotameter is Widely used in petrochemical, steel, electric power,
metallurgy, light industry, food, pharmaceutical,
water treatment and other industries
Range ratio:10:1(Special type 20:1)
Accuracy class:2.5(Special type 1.5% or 1.0%)
Working pressure:?DN15~DN50 PN16MPa (Special type 25MPa).
DN80~DN150 PN10MPa (Special type 16MPa).
Pressure rating of jacket 1.6MPa.
Output:4~20mA/?HART?/RS485?/Alarm?/Pulse
Connection mode:Flange Thread Tri-clamp

Metal tube rotameters are widely used in pe-
troleum, chemical, power generation, pharma-
ceutical, food, water treatment, etc. Complex,
harsh environmental conditions, and a variety
of media conditions in the process of flow
measurement.
Range ratio:10:1(Special type 20:1)
Accuracy class:2.5(Special type 1.5% or 1.0%)
Working pressure:?DN15~DN50 PN16MPa (Special type 25MPa).
DN80~DN150 PN10MPa (Special type 16MPa).
Pressure rating of jacket 1.6MPa.
Output:4~20mA/?HART?/RS485?/Alarm?/Pulse
Connection mode:Flange Thread Tri-clamp

Metal pipe flowmeter consists of measuring pipe, float, indicator and process connection components with the characteristics of small size, wide measuring range, easy installation. In the industry area, it is widely used to measure flow of gas, liquid, and steam, especially suitable for mediums with low current velocity and low flow?rate.
Range ratio:10:1(Special type 20:1)
Accuracy class:2.5(Special type 1.5% or 1.0%)
Working pressure:?DN15~DN50 PN16MPa (Special type 25MPa).
DN80~DN150 PN10MPa (Special type 16MPa).
Pressure rating of jacket 1.6MPa.
Output:4~20mA/?HART?/RS485?/Alarm?/Pulse
Connection mode:Flange Thread Tri-clamp

The flow measurement of the metal rotameter is performed by the transmitter in the indicator by coupling the porcelain steel to feel the change of the float position to complete the flow indication and the remote transmission of the signal. When the measured medium flows through the measuring tube from bottom to top, when the float is balanced by gravity, buoyancy and the vertical upward driving force of the fluid velocity on the float, the float is relatively stationary at a certain position, and this position varies with the distance between the float and the vertebral canal. The ring area and fluid velocity vary, and the position of the float corresponds to the flow rate of the measured medium.

Metal rotor flowmeter, also known as variable area flowmeter, has the characteristics of simple structure, reliable operation, wide application range, accurate measurement and convenient installation. Metal rotor flowmeter has high temperature resistance and high pressure resistance. ZNLZ series metal rotor flowmeter has ordinary metal Rotameter and anti-corrosion metal rotameter, the above two types are divided into field indication type and electric remote transmission type
Range ratio: 10:1(Special type 20:1).
Accuracy class: 2.5(Special type 1.5% or 1.0%).
Working pressure: DN15~DN50 PN16 (Special type 2.5MPa).
Medium temperature: Normalized type -80¡æ~+220¡æ.
Ambient temperature: -40¡æ~+120¡æ(Remote display without LCD¡Ü85¡æ).

The metal tube rotameter adopts the variable area measurement principle and is suitable for measuring liquid and gas. All metal structure, there are indicating type, electric remote transmission type, corrosion-resistant type, high-voltage type, jacket type, explosion-proof type. With 0-10mA, 4-20mA standard analog signal output and field indication. Accumulation, digital communication, on-site modification of measurement parameters, different power supply functions, with magnetic filters and special specifications. Widely used in petroleum, chemical, power generation, pharmaceutical, food, water treatment, etc.