Q&T Waste Water Open Channel Flow Meter ultrasonic water meters

QT811 clamp on ultrasonic flow meter is with specially design with built-in transducers and LCD monitor in one body. Clamp-on transducers are mounted externally on the surface of the pipe and which generate pulses that pass through the pipe wall. The flowing
liquid within causes time differences in the ultrasonic signals, which are then evaluated by the flowmeter to
produce an accurate flow measurement.

Pipe Size:?DN15-DN40mm (1/2¡±~1 1/2¡±)
Flow Range:¡À0.1m/s ~¡À5m/s
Temperature: 0~75¡æ (standard)
Output: 4-20mA, OCT Pulse, RS485
Accuracy:?¡À1% of measured value
Power Supply: DC10-24V

Fixed type clamp on ultrasonic flowmeter with RS485 Modbus flow meter is an ultrasonic flowmeter used to measure the flow rate of liquids in closed pipes. The transducer is a non-contact, clamp-on type, which will provide the benefits of contamination-free operation and ease of installation. The transit time flowmeter employs two transducers, which act as ultrasonic transmitters and receivers. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

PLCM series ultrasonic open channel flow meter is a low cost choice. It is a hot sell product for river channel measuring. The product supports weirs or notches of different standards in various countries and can be widely used for measurement or monitoring of total water drainage.
Display: Backlight LCD
The maximum of Accumulative Flow: 9999999.9 m3/h
Accuracy of Change in Level: 1mm or 0.2% of full span (whichever is greater)
Resolution: 1mm
Analogue Output: 4-20mA, corresponding to instantaneous flow
Relays Output: Standard 2 relay outputs(Optional up to 6 relays)
Serial Communication: RS485, MODBUS -RTU standard protocol
Ambient Temperature: -40 ~70 Degree C
Power Supply: DC24V (+5%) 0.2A; AC220V (+20%) 0.1A ;Optional DC12V

Q&T Wall mounted ultrasonic flowmeter clamp on type transducer is a high precision no-cut tube measurement method. This special design includes matching sensors for ease of use and is ideal for installation in existing systems Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring single clean liquids Power supply: 24VDC/85VAC-2265AC Storage: SD card optional Heat meter optional

This non-contact ultrasonic flow meter that is designed for open channel flow metering working with a flume, weir or any other primary device. Non-contact ultrasonic flow meter require accurate measurement of the surface level of a liquid. A flume, channel or structure which has a known characteristic flow per measured head, together with the measured liquid level, accurately define the flow rate through the system.

Analogue?Output: 4-20mA,?corresponding?to?instantaneous?flow
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS?-RTU?standard?protocol
Ambient?Temperature: -40 ~70 Degree C
Measure?Cycle: 1?second?(selectable?2?seconds?)
Power?Supply: DC24V?(+5%)?0.2A;?AC220V?(+20%)?0.1A?;Optional?DC12V

4-20mA pulse RS485 wall mounted ultrasonic flow meter is a high precision no-cut tube measurement method. This special design includes matching sensors for ease of use and is ideal for installation in existing systems Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring single clean liquids Power supply: 24VDC/85VAC-2265AC Storage: SD card optional Heat meter optional

0.5% accuracy ultraosnic flow meter with multi channel sensor and body mainly be adopted carbon steel material ,can produce stainless stell according to request.
Instantaneous flow,Total flow,Heat,Positive flow,Negative flow
High Isolation voltage,Strong anti-interference,Suppress voltage noise,Good isolation performance
Inline ultrasonic flow meter collect temperature signal and accuracy reach 0.001¡æ
When using inline ultrasonic flow meter to measure,allowing pipe with liner

Handheld Ultrasonic Water flow sensor portable flow meter no pipe cutting required. The user simply clamp on the flow sensor to the pipe surface. Handheld Ultrasonic Water flow sensor portable flow meter can then detect the flow through ultrasonic waves, and then automatically calculate the flow rate value, flow accumulator, etc. No pipe cutting means no damage to the pipe. So as long as the pipes are in good condition, the installation on the flowmeter will not provide the possibility of leakage. Sensor: Clamp-on/External Principle: transmit time Size: DN15mm-DN6000mm Measuring medium: Liquid 3.6V Battery-powered

Industrial ultrasonic flow meter output for water ultrasonic flow meter pvc pipe heat meter is a ideal for liquids such as chemical,visous liquids, and sea water. The non-intrusive, clamp-on ultrasonic flow meter fits pipes between 1/2″ to 48″ internal diameter. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Medium: clean liquids,pure water Built-in rechargeable battery 3.6V Measurment unit: Meter, Feet,Cubic Meter.

Ultrasonic clamp-on flow meter is simple to install and is suitable for large diameter pipes requiring monitoring and flow measurement, as well as a wide network of smaller supply lines. Ultrasonic clamp-on flow meter provide the tools needed to meet the diverse requirements of such a demanding industry. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

Ultrasonic flow meter wall mount ultrasonic flow sensor clamp on type transducer is an ultrasonic flowmeter used to measure the flow rate of liquids in closed pipes. The transducer is a non-contact, clamp-on type, which will provide the benefits of contamination-free operation and ease of installation. The transit time flowmeter employs two transducers, which act as ultrasonic transmitters and receivers. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

DN80mm ultrasonic flowmeter water flow mter is an ultrasonic flowmeter used to measure the flow rate of liquids in closed pipes. The transducer is clamp-on type, which will provide the benefits of contamination-free operation and ease of installation. The transit time flowmeter includes two transducers, which act as ultrasonic transmitters and receivers. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

Precise digital display insertion clamp on ultrasonic water flow meter Wall mounted ultrasonic flowmeter is an ultrasonic flowmeter used to measure the flow rate of liquids in closed pipes. The transducer is a non-contact, clamp-on type, which will provide the benefits of contamination-free operation and ease of installation. The transit time flowmeter employs two transducers, which act as ultrasonic transmitters and receivers. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

Portable Clamp on Sensor Digital Ultrasonic Flow Meter are widely used in tap water, heating, water conservancy, metallurgy, chemical industry, machinery, energy and other industries. It can be used for production monitoring, flow verification, temporary detection, flow inspection, water meter balance debugging, heat network balance debugging, and energy-saving monitoring. It is a tool instrument for timely flow detection. This ultrasonic flowmeter has a built-in data logger. The built-in data logger has a space of 24K bytes and can store 2000 lines of measurement data. The rechargeable power supply has a built-in high-capacity nickel-metal hydride rechargeable battery, which can support the flowmeter to work continuously for more than 12 hours. Measuring accuracy: +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

QT621 Portable ultrasonic flow meter a type of portable instrument for non-invasive, quick flow and energy measurement.Portable ultrasonic flow meter matched precision transducers and signal processing circuitry to accurately measure the flow of most liquids. QT621 ultrasonic flow meter support quickly verify the flow reading of another meter and to data log flow system values over an extended time period.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

QT811 ultrasonic clamp on flow meters are popular used from simple water flow measurements to energy flow monitoring and automated process control. QT811 clamp on ultrasonic flow meter uses clamp-on transducers that are mounted externally on the surface of the pipe and which generate pulses that pass through the pipe wall.

Pipe Size:?DN15-DN40mm (1/2¡±~1 1/2¡±)
Flow Range:¡À0.1m/s ~¡À5m/s
Temperature: 0~75¡æ (standard)
Output: 4-20mA, OCT Pulse, RS485
Accuracy:?¡À1% of measured value
Power Supply: DC10-24V

China wall mounted Clamp on pipe ultrasonic water flow meter price is a high precision no-cut tube measurement method. This special design includes matching sensors for ease of use and is ideal for installation in existing systems Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring single clean liquids Power supply: 24VDC/85VAC-2265AC Storage: SD card optional Heat meter optional

Inline ultrasonic flow meter could connect temperature sensor to become one calorimeter and widely
be used in Process control, Production measurement, Trade settlement and is suitable for continuously measuring flow and heat of clean and uniform liquids without large concentration suspended particles or gases industrial environment¡£
Support single channel and multi-channel at the same time,when one of channel is abnormal or not connected,it can automatically switch to single channel to working .

Flange ultrasonic flow meter could be manufactured from 50mm~700mm and mainly be used to measure the flow and heat of clean liquid which don’t contain large concentration of suspended particles or gas.
No moving parts, no wear, no pressure loss,Maintenance-free
Measuring conductivity liquid and Non-conductivity liquid
Can measure zero-flow
2 way input
4-20mA,Pulse,OCT,RS485
Bi-directional flow measurement
Backlit LCD
Measuring up to 100 times/s
Accuracy:¡À0.5%

Ultrasonic flow measurement according to the ¡°differential transit time¡± method: This method uses two sensors, set opposite each other in the measuring tube. Each sensor can alternately transmit and receive ultrasonic signals, while simultaneously measuring the signal transit time.
Measuring cycle:50mS
Output:4~20mA,Pulse,OCT,RS485
Body material:Standard carbon steel,SS304 and SS316 are optional
Power supply:DC24V and AC220V

DN80 pipe ultrasonic flowmeter water liquid ultrasonic clamp on type is an ultrasonic flowmeter used to measure the flow rate of liquids in closed pipes. The transducer is clamp-on type, which will provide the benefits of contamination-free operation and ease of installation. The transit time flowmeter includes two transducers, which act as ultrasonic transmitters and receivers. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

Wall mounted Ultrasonic Flow meter Data Logger Digital Ultrasonic chemical Liquid Flow Meter is an ultrasonic flowmeter used to measure the flow rate of liquids in closed pipes. The transducer is clamp-on type, which will provide the benefits of contamination-free operation and ease of installation. The transit time flowmeter includes two transducers, which act as ultrasonic transmitters and receivers. The transducer can be installed in a v-type method, where the sound travels through the pipe twice, a w-type method, where the sound travels through the pipe four times. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

Q&T brand pulse output ultrasonic flow meter is one kind of economy type flow meter for liquid,multi channle type inline ultrasonic flow meter accuracy less 0.5%
Inline ultrasonic flow meter support single channel and multi-channel at the same time,when one of channel is abnormal or not connected,it can automatically switch to single channel to working
OCT output
RS485 communication
Input:Two-wire PT1000

This irrigation flow meter is a professional economic and practical instrument during agriculture, industry research and development. It is a non-contact measurement and can be applied in even harsh environments. This Open channel Irrigation flow meter can directly display the instantaneous and cumulative flow.
Power Supply: DC24V (+5%) 0.2A; AC220V (+20%) 0.1A ;Optional DC12V
Flow Rate Range: 0.0000~99999L/S or m3/h
The maximum of Accumulative Flow:  9999999.9 m3/h
Analogue Output: 4-20mA, corresponding to instantaneous flow
Relays Output: Standard 2 relay outputs(Optional up to 6 relays)
Serial Communication: RS485, MODBUS -RTU standard protocol
Ambient Temperature: -40 ~70 Degree C

This solar power Open Channel Water Meters consists of two elements, a host, which has display and an integral keypad for programming, and a transducer/probe, which must be mounted directly above the surface to be measured. It can be widely applied to the environmental protection, water treatment, irrigation, chemical, and other industries.

Specifications:
Display: Backlight?LCD
Flow?Rate?Range: 0.0000~99999L/S?or?m3/h
The?maximum?of Accumulative Flow: 9999999.9?m3/h
Accuracy?of?Change in Level: 1mm?or?0.2%?of?full?span?(whichever?is?greater)
Resolution: 1mm
Analogue?Output: 4-20mA,?corresponding?to?instantaneous?flow
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS?-RTU?standard?protocol

High Precision Portable Digital Ultrasonic Flowmeter is a portable liquid flow measurement device with a sensor. This High Precision Portable Digital Ultrasonic Flowmeter adopt transit-time ultrasonic measurement technology for superior accuracy and ease of installation and installation. This easy-to-use flowmeter comes in a rugged, waterproof carrying case for easy transport of the display, sensor, and cables between measurement locations. High accuracy +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

With ultrasonic flow meters, the flow of liquids can be measured reliably – independent of conductivity, pressure, temperature, and in applications where traceability and guaranteed accuracy are required, the external ultrasonic sensor is the first choice. Clamp-on ultrasonic sensors, on the other hand, are mounted on the outer wall of the pipe and can therefore also be used for temporary measurements.
Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Built-in rechargeable battery 3.6V Communication: RS232

This open channel flow meter uses ultrasonic principle to measure the water level height in the open channel weir, and then the microprocessor calculates the corresponding flow value automatically. The level value is converted to a particular flow in a particular weirs/flumes, so accurate level values are important. It is a sensor designed for open channel flow to provide accurate level readings.
Power Supply: DC24V (+5%) 0.2A; AC220V (+20%) 0.1A ;Optional DC12V
Flow Rate Range: 0.0000~99999L/S or m3/h
Analogue Output: 4-20mA, corresponding to instantaneous flow
Relays Output: Standard 2 relay outputs(Optional up to 6 relays)
Serial Communication: RS485, MODBUS -RTU standard protocol
Ambient Temperature: -40 ~70 Degree C

Ultrasonic Irrigation Open channel flow meter is for measuring water flow rates in irrigation channels, streams, and storm water systems. Open Channel Flow Meter can be used for continuous measuring of municipal rain-water, wastewater, sewage discharge and irrigation water pipelines.We have both transit-time ultrasonic open channel flow meter and doppler type ultrasonic open channel flow meter.

Specifications:
Analogue?Output: 4-20mA,?corresponding?to?instantaneous?flow
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS?-RTU?standard?protocol
Ambient?Temperature: -40 ~70 Degree C
Measure?Cycle: 1?second?(selectable?2?seconds?)
Power?Supply: DC24V?(+5%)?0.2A;?AC220V?(+20%)?0.1A?;Optional?DC12V

Wall Mounted Ultrasonic Flowmeter flow meter can be used with various types of detectors applicable for small to large diameter pipe (0.5″” to 236″” / 15mm to 6000mm) and low to high temperature (?30 to +160¡ãC).
This wall mounted flow meter is designed for 12 hours of continuous operation with a built-in battery ,allows flow, velocity and total data to be stored. Though RS232 to connect with a PC to facilitate configuring the storage as well as saving and reading data files.
Accuracy: +/-1.0% of FS
Wide range: DN15mm-DN6000mm
Measuring clean liquids
Power supply: 24VDC/85VAC-2265AC
Communication: RS485