Clamp on type sensor ultrasonic water flow meter

Ultrasonic flow meter with RS232 communication for clean liquid is a non-contact instrument, which can measure the flow of medium with large diameter and can also be used for the measurement of medium that is not easy to contact and observe. Its measurement accuracy is very high, and the external clip-type installation can reach the highest accuracy of ¡À1.0%. It is almost not disturbed by various parameters of the measured medium, especially it can solve the strong corrosiveness, non-conductivity, Flow measurement of radioactive and flammable and explosive media. Measuring accuracy: +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

For the Open Channel Water Meters, the level sensor is mounted on the top of the flume, and ultrasonic wave is transmitted by the probe to the surface of the monitored material. Instead of using mass or volumetric data to determine the rate of flow of a substance, open channel flow meters monitor the relationship between the depth of the liquid and the flow rate.Open Channel Flow Meter can be used for continuous measurement of municipal rainwater, wastewater, sewage discharge and irrigation water pipelines.

Specifications:
Sensor?Level?Range: 0-4.0m; other?level?range?also?available
Blind?zone: 0.20m
Temperature?Compensation: Integral?in?probe
Pressure?Rating: 0.2MPa
Beam?Angle: 8*?(3db)
Cable?Length: 10m?standard?(can?be?extended?to?1000m)
Sensor?Material: ABS,?PVC?or?PTFE?(optional)
Sensor?Protection Class: IP68

Handheld Ultrasonic Flow Meter(QTDS-100H)- Wide range of applications,with clamp on transducers to measure flow rate through the pipe wall, the transit time ultrasonic flow principle. It is a 3.6V battery powered ultrsonic flow meter, for using on a wide range of sizes and can provide 24 hours measurement continuely. Accuracy: +/-1.0% of FS Wide range: DN300mm-DN6000mm Measuring clean liquids Built-in rechargeable battery 3.6V 2000 lines storage Communication: RS232

0.5% accuracy ultraosnic flow meter with multi channel sensor and body mainly be adopted carbon steel material ,can produce stainless stell according to request.
Instantaneous flow,Total flow,Heat,Positive flow,Negative flow
High Isolation voltage,Strong anti-interference,Suppress voltage noise,Good isolation performance
Inline ultrasonic flow meter collect temperature signal and accuracy reach 0.001¡æ
When using inline ultrasonic flow meter to measure,allowing pipe with liner

QT621 ultrasonic flow meter is a type of portable flow meter with the main advantage of support to be easily moved and installed in different pipes and convenient to carry site to site. Portable type ultrasonic flow meters are widely used in all areas such as drinking water and sewerage industry, power plants, producing industry, food industry and so on.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

China wall mounted Clamp on pipe ultrasonic water flow meter price is a high precision no-cut tube measurement method. This special design includes matching sensors for ease of use and is ideal for installation in existing systems Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring single clean liquids Power supply: 24VDC/85VAC-2265AC Storage: SD card optional Heat meter optional

Ultrasonic Flow meter for applications in clean water and in low conductivity media. Operating principle based on transit time measurement.
Pipe material:Steel,Stainless steel,Cast iron,PVC,Cement pipe and allow pipe with lining
High Isolation voltage,Strong anti-interference,Suppress voltage noise,Good isolation performance
Inline ultrasonic flow meter collect temperature signal and accuracy reach 0.001¡æ
Viscosity:0.1~10m/s
Measuring cycle:50mS
Output:4~20mA,Pulse,OCT,RS485
Body material:Standard carbon steel,SS304 and SS316 are optional
Power supply:DC24V and AC220V

DN80 pipe ultrasonic flowmeter water liquid ultrasonic clamp on type is an ultrasonic flowmeter used to measure the flow rate of liquids in closed pipes. The transducer is clamp-on type, which will provide the benefits of contamination-free operation and ease of installation. The transit time flowmeter includes two transducers, which act as ultrasonic transmitters and receivers. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

Wall mounted and handhold portable clamp on ultrasonic water flow meter battery ultrasonic flowmeter adopts the self-development measurement technology.This measurement technique is a faster and more accurate process time measurement algorithm. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring single clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

Clamp on pvc water flow meter ultrasonic flowmeter provide industry-leading flow measurement accuracy. With a small package that saves costs in shipping. Plus flow meters are ideal for industries that measure liquid flow without cutting pipes, such as chemical, pharmaceutical, mining, power, chemical, water and wastewater, HVAC, food and beverage, and more. It can also be used as a non-invasive detector
High accuracy +/-1.0% of FS
Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC
Measuring clean liquids
Battery-powered,for 12 hours
Communication: RS232

This irrigation flow meter is a professional economic and practical instrument during agriculture, industry research and development. It is a non-contact measurement and can be applied in even harsh environments. This Open channel Irrigation flow meter can directly display the instantaneous and cumulative flow.
Power Supply: DC24V (+5%) 0.2A; AC220V (+20%) 0.1A ;Optional DC12V
Flow Rate Range: 0.0000~99999L/S or m3/h
The maximum of Accumulative Flow:  9999999.9 m3/h
Analogue Output: 4-20mA, corresponding to instantaneous flow
Relays Output: Standard 2 relay outputs(Optional up to 6 relays)
Serial Communication: RS485, MODBUS -RTU standard protocol
Ambient Temperature: -40 ~70 Degree C

Natural gas thermal gas mass flow meter is one of kind mass flow meter which is popular in industrial applications is the way they are designed and built. The feature is no moving parts, nearly unobstructed straight through flow path, require no temperature or pressure corrections and retain accuracy over a wide range of flow rates.
Viscosity:0.1~10m/s
Measuring cycle:50mS
Output:4~20mA,Pulse,OCT,RS485
Body material:Standard carbon steel,SS304 and SS316 are optional
Power supply:DC24V and AC220V

Wall Mounted ultrasonic water flow meter Clamp on transducer adopts the self-development measurement technology.This measurement technique is a faster and more accurate process time measurement. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring single clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

Q&T Modbus Digital Ultrasonic Fluid Flow Meter Clamp On Ultrasonic Flowmeter provide you with an accurate, easy-to-install flow meter. wall mount flow sensor feature quick, easy clamp-on sensor installation, configuration, and a user-programmable menu-driven interface for easy commissioning in the field. Q&T Modbus Digital Ultrasonic Fluid Flow Meter Clamp On Ultrasonic Flowmeter use a special technology to ensure highly accurate flow measurement. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring single clean liquids Power supply: 24VDC/85VAC-2265AC Storage: SD card optional Heat meter optional

Q&T solar power Open Channel flow meter measures level, flow rate and total volume of water flowing through weirs, flumes and channels. The flow meters use a non-contact level sensor. Application field£º
1. Water and sewage treatment£ºpump room, collection well, biochemical reaction
tank, sedimentation tank.
2. Electricity, mines£ºmortar pool, coal slurry pool, butter storage tank, stockyard
or some mobile equipment control, etc.
3. Food industry£ºwineries, granaries, storage tanks for food materials, etc.

Specifications:
Display: Backlight?LCD
The?maximum?of Accumulative Flow: 9999999.9?m3/h
Resolution: 1mm
Analogue?Output: 4-20mA
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS RTU
Ambient?Temperature: -40 ~70 Degree C
Power?Supply: DC24V, AC 220V£»Optional?DC12V

This Solar power GPRS Open Channel Flow Meter can be used for continuous measuring of municipal rain-water, wastewater, sewage discharge and irrigation water pipelines. This Open Channel flow meter measures level, flow rate and total volume of water flowing through weirs, flumes, and channels etc.

Specifications:
Display: Backlight?LCD
Flow?Rate?Range: 0.0000~99999L/S?or?m3/h
The?maximum?of Accumulative Flow: 9999999.9?m3/h
Accuracy?of?Change in Level: 1mm?or?0.2%?of?full?span?(whichever?is?greater)
Resolution: 1mm
Analogue?Output: 4-20mA,?corresponding?to?instantaneous?flow
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS?-RTU?standard?protocol

Handheld water flowmeter portable ultrasonic clamp on type flow meter is a portable liquid flow measurement device with a sensor. Handheld water flowmeter portable ultrasonic clamp on type flow meter proven transit-time ultrasonic measurement technology for superior accuracy and ease of installation and installation. This easy-to-use flowmeter comes in a rugged, waterproof carrying case for easy transport of the display, sensor, and cables between measurement locations. High accuracy +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

Inline ultrasonic flow meter support single channel and multi-channel at the same time,when one of channel is abnormal or not connected,it can automatically switch to single channel to working
Ultrasonic flow measurement according to the ¡°differential transit time¡± method: This method uses two sensors, set opposite each other in the measuring tube. Each sensor can alternately transmit and receive ultrasonic signals, while simultaneously measuring the signal transit time.
Output:4~20mA,Pulse,OCT,RS485
Body material:Standard carbon steel,SS304 and SS316 are optional
Power supply:DC24V and AC220V
Connection way:Flange type
Media temperature :-30~+150¡æ

QT621 ultrasonic flow meter is a type of portable flow meter, which support easily moved and installed in different pipes and convenient to carry site to site. The innovative design includes matched precision transducers
and signal processing circuitry to accurately measure the flow of most liquids over a wide range of velocities.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

Digital Ultrasonic Water Flowmeter Wall Mounted Relay alarm and RS485 Modbus flow meters can realize to measure flow.Connect with temperature sensor,it can measure heat flow.

The Q&T ultrasonic water flow meter that is designed for open channel flow metering, whether you have a flume, weir or any other primary device. This 4-20mA output open channel flow meter has 4-20mA, RS485 and relay output, which is a good choice for different needs of channel flow monitoring.

Analogue?Output: 4-20mA,?corresponding?to?instantaneous?flow
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS?-RTU?standard?protocol
Ambient?Temperature: -40 ~70 Degree C
Measure?Cycle: 1?second?(selectable?2?seconds?)
Power?Supply: DC24V?(+5%)?0.2A;?AC220V?(+20%)?0.1A?;Optional?DC12V

Factory supplier Digital Ultrasonic Flow meter pulse output flowmeter is easy to use, fast to measure flow. It is a popular flowmeter for sewage environmental monitoring departments and large-diameter tap water flow measurement. Factory supplier Digital Ultrasonic Flow meter pulse output flowmeter has the characteristics of large measurement range, and different types of sensors can be used, which can realize the measurement of pipeline flow with diameters of DN20~DN6000mm. High-precision measurement, the measurement accuracy is better than ¡À1%, the linearity is 0.5%, and the repeatability accuracy is 0.2%. Non-contact measurement The Factory supplier LCD displayer digital ultrasonic flow meter sensor is adsorbed on the outer wall of the pipe to complete the flow measurement. Measuring accuracy: +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Built-in rechargeable battery 3.6V Communication: RS232

This river flow meter can directly display the instant and accumulative flow. This Open Channel Water Meter is based on the flow rate-water level calculation method, and adopts an advanced flow rate measuring instrument and water level measuring instrument to ensure a new intelligent high quality flow system.

Specifications:
Sensor?Level?Range: 0-4.0m; other?level?range?also?available
Blind?zone: 0.20m
Temperature?Compensation: Integral?in?probe
Pressure?Rating: 0.2MPa
Beam?Angle: 8*?(3db)
Cable?Length: 10m?standard?(can?be?extended?to?1000m)
Sensor?Material: ABS,?PVC?or?PTFE?(optional)
Sensor?Protection Class: IP68
Output: 4-20mA, Relays, RS485

Q&T Open Channel flow meter measures level, flow rate and total volume of water flowing through weirs, flumes and channels. The flow meters use a non-contact level sensor. Application field£º
1. Water and sewage treatment£ºpump room, collection well, biochemical reaction
tank, sedimentation tank.
2. Electricity, mines£ºmortar pool, coal slurry pool, butter storage tank, stockyard
or some mobile equipment control, etc.
3. Food industry£ºwineries, granaries, storage tanks for food materials, etc.

Specifications:
Display: Backlight?LCD
The?maximum?of Accumulative Flow: 9999999.9?m3/h
Resolution: 1mm
Analogue?Output: 4-20mA
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS RTU
Ambient?Temperature: -40 ~70 Degree C
Power?Supply: DC24V, AC 220V£»Optional?DC12V

With RS485, the ultrasonic open channel flowmeter can be equipped with a communication interface, which is easy to connect with SCADA systems to achieve industrial remote monitoring and control. This Open Channel flow meter measures level, flow rate and total volume of water flowing through weirs, flumes, and channels etc.

Specifications:
Sensor?Level?Range: 0-4.0m; other?level?range?also?available
Blind?zone: 0.20m
Temperature?Compensation: Integral?in?probe
Pressure?Rating: 0.2MPa
Beam?Angle: 8*?(3db)
Cable?Length: 10m?standard?(can?be?extended?to?1000m)
Sensor?Material: ABS,?PVC?or?PTFE?(optional)
Sensor?Protection Class: IP68

4-20mA Output Ultrasonic Water Flow Meter BTU meter is designed to work with clamp-on transducers to enable the flow of a liquid within a closed pipe to be measured accurately without needing to insert any mechanical parts through the pipe wall or protrude into the flow system.

Non-contact Open Channel flow meter measures level, flow rate and total volume of water flowing through weirs, flumes and channels. The flow meters use a non-contact level sensor. Application field£º
1. Water and sewage treatment£ºpump room, collection well, biochemical reaction
tank, sedimentation tank.
2. Electricity, mines£ºmortar pool, coal slurry pool, butter storage tank, stockyard
or some mobile equipment control, etc.
3. Food industry£ºwineries, granaries, storage tanks for food materials, etc.

Specifications:
Display: Backlight?LCD
The?maximum?of Accumulative Flow: 9999999.9?m3/h
Resolution: 1mm
Analogue?Output: 4-20mA
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS RTU
Ambient?Temperature: -40 ~70 Degree C
Power?Supply: DC24V, AC 220V£»Optional?DC12V

Portable clamp on ultrasonic flowmeter Water flow meter price handheld water flow meter for pipe handheld ultrasonic flowmeter is a portable liquid flow measurement device with a sensor. Hot sales portable ultrasonic flowmeter handheld water flow meter adopt transit-time ultrasonic measurement technology for superior accuracy and ease of installation and installation. This easy-to-use flowmeter comes in a rugged, waterproof carrying case for easy transport of the display, sensor, and cables between measurement locations. High accuracy +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

Clamp-on ultrasonic flow meters showcase the benefits of digital signal processing: market-leading accuracy, noise immunity and reliability,liquid ultrasonic flow meter popular in many industry. Flow range:± 0.09ft/s ~ ±16ft/s (±0.03m/s ~ ±5m/s);
Outputs:Analog output:4~20mA,max load 750Ω,Pulse output: 0~10KHz;
Communication: RS232/RS485 Mod bus:
Power supply:10~36VDC/1A;
Display:240*128 back lit LCD;

Ultrasonic flow meter is designed to measure liquid velicity and flow rate in the pipe.
When install the wall mounted ultrasonic flow meter,user don’t need to cut pipe.Just install the flow trasducer in the surface of pipe.So ultrasonic flow meter is one non-contact instrument.
Pipe size:25~1200mm
Accuracy:±1.0%
Output:4-20mA,RS485
Transducer temperature:-40~80℃
Transducer protect:IP68
Power supply:24VDC
SD card