Integral display gas mass flowmeter tri-clamp body thermal flow meter

Thermal gas mass flow meter be adopted LCD converter and its most commonly used to measure the mass flow of clean gases, such as air, nitrogen, hydrogen, helium, ammonia, argon, and other industrial gases.
According to the connect,thermal gas mass flow meter have flange type,thread type,tri-clamp type,wafer type,inertion type etc.
Media:All gas except acetylene and humid gas
Measure range:1:100
Sesnsor working temperature:-20~220℃
Transmitter working temperature:-20~45℃
Output:4-20mA

Gas mass flow meter thermal flowmeters can measure many kinds of dry gas,except acetylena and humid gas.
According to the connection,can produce Flange type,Thread type,Wafer type,Tri-clamp type,Insertion type.
Thermal gas mass flow meter can with DC 4-20mA four-wire output,which is more convenient for remote reception

Thermal gas mass flow meter with LCD display,can display volume flow rate,mass flow rate,
total flow and temperature.
Insertion type thermal gas mass flow meter accuracy is 1.5%
Inline type thermal gas mass flow meter accuracy is 1.0%

Natural gas thermal mass flow meters measure the mass flowrate of fluids by measuring the heat conducted from a heated surface to the flowing fluid. Since a flowing fluid removes a known quantity of heat as it passes, the temperature difference between the heated sensor and the flow stream is directly proportional to the mass flow rate.
With RS485 or HART communication
Power supply:24VDC ,220VAC
Accuracy:¡À1.0%~¡À1.5%

Thermal gas mass flow meter mainly measure various of gases ,special dry gases,but thermal gas mass flow meter can’t measure acetylene.
In many applications, the thermal properties of the fluid can be dependent upon fluid composition. In such applications, varying composition of the fluid during actual operation can affect the thermal flow measurement. Therefore, it is important for the thermal flow meter supplier to know the composition of the fluid so that the proper calibration factor can be used to determine the flow rate accurately
Widly flow range ratio:1:100
Display:4 line digital
With RS485 or HART communication
Power supply:24VDC ,220VAC
Accuracy:¡À1.0%~¡À1.5%

Thermal gas mass flowmeters are suitable for all industrial and test rig applications that demand quick and precise gas measurement. The flowmeters directly indicate the mass flow or normalized volume flow of gases without any additional pressure and temperature compensation. They have an impressively high accuracy, short response time and a very wide flow range with virtually no loss of accuracy even at the lowest flow rates.
Mass flow
SS304 rod
Dual power:24VDC,220VAC
Min.Flow velocity:0.1Nm/s
Online installation

SS304 is the standard material for thermal gas mass flow meter and thermal flow meter is digital display and can
with RS485 or HART communication
Sesnsor working temperature:-20~220¡æ
Transmitter working temperature:-20~45¡æ
Thermal gas flow meter can measure many kinds of gases except acetylene and humid gas and m,easure range can reach 1:100,so it usually be used for leak detection

4-20mA ouput thermal gas mass flow meter is on kind flow meter for direct mass measurementt of Air,N2, CO2,Natrual gas ect.
Whenever low pressure loss is important in gas industry thermal mass flowmeters offer a real alternative to traditional measuring techniques.
Whatever for process control, consumption and supply monitoring, detecting leaks or monitoring distribution networks. Using insertion versions, it is also possible to measure gas flows in very large pipelines or in rectangular ducts.

Thermal gas mass flow meter is one of kind mass flow meter which is popular in industrial.
Q&T gas mass thermal flow meters are be calibrated by gas venturi sonic nozzle calibration device,and ensure the thermal gas mass flowmeter accuracy can reach 1.0% and 1.5%.
Volume flow /Mass flow
SUS304 body
MODBUS RTU RS485
0.1~100Nm/s
4 lines LCD
EX-PROOF

Thermal flow sensor temp is always 30¡æ higher than the medium temperature (environment temperature), and the meter adopts method of constant differential temperature, therefore the meter don¡¯t need temperature and pressure compensation in principle
Power supply:DC24V and AC220V
Output:4-20mA,Pulse,RS485
Body material:Standard SS304,and SS316 is optional
Velocity:0.1~100Nm/s
Media temperature:-40~+220¡æ

Thermal gas mass flow meter is one kind of precision instrument,ensuring the accuracy is important.
Q&T adopt the critical flow nozzle calibration device to calibrate each gas mass flow meter,the calibration device flow range can reach Min. 0.5m3/h and Max.10000 m3/h .
Nozzle calibration device more ensure the flow meters’ accuracy
Accuracy:
In-line type accuracy:¡À1.0%
Insertion type accuracy::¡À1.5%
Power supply:DC24V and AC220V
Output:4-20mA,Pulse,RS485
Body material:Standard SS304,and SS316 is optional

As the flow meter final manufacturer,OEM and ODM are very normal ,such as Color,Material,Display,Output,Process Connect,Function etc.
Q&T brand thermal mass flowmeters are suitable for all industrial and test rig applications that demand quick and precise gas measurement. The flowmeters directly indicate the mass flow or normalized volume flow of gases without any additional pressure and temperature compensation. They have an impressively high accuracy, short response time and a very wide flow range with virtually no loss of accuracy even at the lowest flow rates.
DC4-20mA four-wire output
Flow unit:Nm3
SS304 rod
All gas except acetylene and humid gas
Measure range:1:100
Sesnsor working temperature:-20~220¡æ
Transmitter working temperature:-20~45¡æ

Thermal mass flowmeters are suitable for all industrial and test rig applications that demand quick and precise gas measurement.
Thermal air mass flow meter be adopted the critical flow nozzle calibration device to calibrate each gas mass flow meter,the calibration device flow range can reach Min. 0.5m3/h and Max.10000 m3/h .
Widely turndown ratio:100:1
Power supply:24VDC&220VAC
Response time:1S

Thermal meters require a fully developed flow profile as a prerequisite for correct flow measurement.
When the gas is very humid or saturated with water (e. g. Bio Gas), the piping and flowmeter body should be insulated to prevent water droplets condensing on the measuring sensor.
DC4-20mA four-wire output
Mass flow unit
Dual power:24VDC,220VAC
Min.Flow veloctiy:0.1Nm/s
Output:4-20mA

Thermal gas mass flow meter is one kind of precision instrument,ensuring the accuracy is important.
Q&T adopt the critical flow nozzle calibration device to calibrate each gas mass flow meter,the calibration device flow range can reach Min. 0.5m3/h and Max.10000 m3/h .
Nozzle calibration device more ensure the flow meters’ accuracy

Except insert type,Q&T also can manufacture Flange thermal flow meter,Thread thermal flow meter ,Wafer type thermal flow meter,Tri-clamp type thermal flow meter .
Q&T also can do OEM for clients,such as Display,Color,Output etc.
Insertion type:DN32~DN4000
Flange type:DN10~DN300
Tri-clamp type :DN10~DN100
Thread type:DN10~DN100

Thermal gas mas flow meters are measuring the mass flow or volume flow of gas,flow range can do 0.5Nm/s¡«100Nm/s. So this meter also can be used for gas leak detection.
Thermal flow sensor temp is always 30¡æ higher than the medium temperature (environment temperature), and the meter adopts method of constant differential temperature, therefore the meter don¡¯t need temperature and pressure compensation in principle.
Accuracy:
In-line type accuracy:¡À1.0%
Insertion type accuracy::¡À1.5%
Power supply:DC24V and AC220V
Output:4-20mA,Pulse,RS485
Body material:Standard SS304,and SS316 is optional
Velocity:0.1~100Nm/s
Media temperature:-40~+220¡æ

Thermal gas mass flow meter be adopted LCD converter and its most commonly used to measure the mass flow of clean gases, such as air, nitrogen, hydrogen, helium, ammonia, argon, and other industrial gases.
According to the connect,thermal gas mass flow meter have flange type,thread type,tri-clamp type,wafer type,inertion type etc.
With RS485 or HART communication
Power supply:24VDC ,220VAC
Accuracy:¡À1.0%~¡À1.5%

4-20mA ouput thermal gas mass flow meter is on kind flow meter for direct mass measurementt of Air,N2, CO2,Natrual gas ect.
Whenever low pressure loss is important in gas industry thermal mass flowmeters offer a real alternative to traditional measuring techniques.
Whatever for process control, consumption and supply monitoring, detecting leaks or monitoring distribution networks. Using insertion versions, it is also possible to measure gas flows in very large pipelines or in rectangular ducts.
Media:All gas except acetylene and humid gas
Measure range:1:100
Sesnsor working temperature:-20~220℃
Transmitter working temperature:-20~45℃
Output:4-20mA
Accuracy:±1.0%~±2.5%
Probe material:SS316L
Power supply:24VDC ,220VAC
Response time:1S
Display:4 line digital

Q&T gas mass thermal flow meters are be calibrated by gas venturi sonic nozzle calibration device,and ensure the thermal gas mass flowmeter accuracy can reach 1.0% and 1.5%.
When calibrate thermal flow meter,Q&T will choose four flow velocity points ,then calibrate 3 times each velocity point
Media:All gas except acetylene and humid gas
Measure range:1:100
Sesnsor working temperature:-20~220℃
Transmitter working temperature:-20~45℃
Output:4-20mA

For the insertion type instrument, on the premise that both the measuring media and field environment are applicable for online dismantlement with non-stop operation, it is viable to have maintenance operation with non-stop operation relying on its special structure.
Velocity:0.1~100Nm/s
Media temperature:-40~+220¡æ
Size£º
Insertion type:DN32~DN4000
Flange type:DN10~DN300
Tri-clamp type :DN10~DN100
Thread type:DN10~DN100

Thernal gas flow meter is one kind smart gas flow instrument, It can easily and accurately detect the mass flowrate of gas,specical for low flowrate.
Such as :Air, Nitrogen, Hydrogen, Oxygen, Chlorine, Natural gas, Flue gas and Other gases (except acetylene gas)
Thermal gas mass flow emter be widely used in the process control and gas flow measurement of petroleum, chemical industry, metallurgy, electric power, water treatment, papermaking, food, medicine, cement, textile and various production and scientific research institutions.
Media:All gas except acetylene and humid gas
Measure range:1:100
Sesnsor working temperature:-20~220℃
Transmitter working temperature:-20~45℃
Output:4-20mA
Accuracy:±1.0%~±2.5%
Probe material:SS316L
Power supply:24VDC ,220VAC
Response time:1S
Display:4 line digital

Q&T brand thermal gas flow meter adopt gas venturi sonic nozzle calibration device regular insprction and verification guarantee accuracy and reliability of the calibration device.
According to clients request,Q&T also can apply the CNAS certificates for the thermal flow meter
Media:All gas except acetylene and humid gas
Measure range:1:100
Sesnsor working temperature:-20~220℃
Transmitter working temperature:-20~45℃
Output:4-20mA

Pulse output thermal gas mass flow meter is one of kind mass flow meter which is popular in industrial applications is the way they are designed and built. The feature is no moving parts, nearly unobstructed straight through flow path, require no temperature or pressure corrections and retain accuracy over a wide range of flow rates.
Media:All gas except acetylene and humid gas
Measure range:1:100
Sesnsor working temperature:-20~220℃
Transmitter working temperature:-20~45℃
Output:4-20mA
Accuracy:±1.0%~±2.5%
Probe material:SS316L
Power supply:24VDC ,220VAC
Response time:1S
Display:4 line digital

Thermal gas mass flow meter with DC4-20mA four-wire output,which is more converient for remote reception.Support MODBUS RTU RS485 protocol,coording the receiving system to collect more data and modify system and Q&T brand thermal gas mass flow meter already got CE ,Ex-Proof certificates
Pressure:
Insertion type¡Ü1.6Mpa
Flange type ¡Ü4.0Mpa

According the installation,thermal gas mass flow meter is divide into insertion type and inline type.
Whatever insertion or inline gas mass flow meter,they all have no moving parts and measure the mass of the fluid directly.This make thermal gas mass flow meter measure the standardized volumetric flow rates and totals without the need for temperature or pressure compensation
Velocity:0.1~100Nm/s
Output:4-20mA,Pulse,RS485
Body material:SS304
Alarm output:1-2 relay
Pressure up to 4.0Mpa

Thermal flow meter is one kind of gas mass flow meter, can display mass flow rate and total mass flow
According to request, Q&T can do OEM ,such as display converter color,Display LOGO,Flow unit etc.
Output is 4-20mA,Pulse
Communication is RS485 or HART

Tri-clamp thermal gas mass flow meter body be adopted SS304 and probe is SS316
Tri-clamp connect is fast to install and it no moving parts, nearly unobstructed straight through flow path, require no temperature or pressure corrections and retain accuracy over a wide range of flow rates.
Tri-clamp thermal gas mass flow meter size from DN15~DN100mm

The thermal gas flowmeter is mainly used for measuring gas with low flow and the range could reach 1:100,which is btter than gas flowmeter on market and low flow could be measured,the min.flow velocity can reach 0.1Nm/s and Max. velocity reach 100Nm/s
Media:All gas except acetylene and humid gas
Measure range:1:100
Sesnsor working temperature:-20~220℃
Transmitter working temperature:-20~45℃
Output:4-20mA

Q&T thermal gas mass flow meter with DC4-20mA four-wire output,which is more convenient for remote reception.Support MODBUS RTU RS485 protocol,coordinating the receiving system to collect more data ans modify system
Insertion rod diameter :
DN32~DN50 standard rod dia. 12mm ,14mm is optional
DN65~DN4000 standard rod dia.19mm,12mm and 14mm is optional