Intelligent explosion proof aluminum alloy gas roots flow meter

QTWG series turbine gas meter is designed to perform on the high level of accuracy, which is an ideal product for commercial and industrial uses. All the measured values can be displayed and are available on the modbus interface.

Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

Turbine Flow Meter is a volumetric measuring turbine type of Impeller Flow meters , made up of Sensor and Convertor. The flowing fluids engages the rotor causing it to rotate at an angular velocity proportional to the fluid flow rate.The Sensor reacts to the average velocity of fluid with multi-blades rotor so as to speculating the flow value and the accumulative flow value.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART
LCD display

A turbine flow meter is a volumetric metering the meter consists of a rotor and bearing assembly Suspended on a shaft, which is mounted to a support device.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

Turbine Flowmeters are the optimum combination of useful range, corrosion resistance, and operating life for a particular application. A low mass rotor design allows for a rapid dynamic response which permits the turbine flowmeter to be used in pulsating flow applications.

Works well with Low viscosity liquids. The turbine turns when the good passes through and a pulsed counter provides the flow total on a digital display.Works well with Low viscosity liquids. The turbine turns when the good passes through and a pulsed counter provides the flow total on a digital display.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART

turbine flow meter features
-Simple structure,light weight.
-High measuring precision, andgood reproducibility, sensitive response, convenient installation and maintenance
-4-20mA two-wire current output, pulse output.
-Can measure liquid, water, oil and fuel with low viscosity and no impurities

Turbine flowmeters utilize flow measurement technology to render exceptionally reliable and accurate digital outputs. Our high-quality industrial flowmeters are maintainable, durable, and versatile. These versatile turbine flowmeters measure an extensive range of liquids, vapors in pipes, such as chemicals, hydrocarbons, cryogenic liquids, water, and industrial gases.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

liquid turbine flow meter is a new type of intelligent instrument with integrated turbine flow sensor and display product calculation developed by advanced ultra-low power single-chip microcomputer technology
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

QTWG series natural gas flow meters adopt import impeller material which could ensure high accuracy in working life. Turbine gas meters offer high quality measurement solution for varous kinds of clean gas which could increase working efficiency in gas transmission, distribution and industrial applications etc.
Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

QTLL series rotary gas meters a high-quality positive displacement roots-type gas meter that is available in a variety of sizes and options. Rotary type gas meters allow for measurement of large amounts of gas flow in a compact gas meter. The rotary gas meter can be used indoors or outdoors.
Size:DN25-200mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Installation: Vertical or Horizontal
Accuracy:1.5% or 1.0%

turbine flow meter can be used for liquid flow measurement such as water and oil in the pipe size of DN4 ~ DN200 mm, 1.0%R measuring accuracy, 24V DC power supply, threaded or flange connection.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART

turbine flow meter adapts to measure the liquid rate and total flowrate of low viscosity. It can be widely used in the fields of Petrol, Chemical industry, Metallurgy, Scientific research for measuring or control. Several output and display methods can be selected.

Gas turbine flow meter is type of very popular flow meter for natural gas, LPG gas flow measurement. Gas turbine flow meter as a smart meter, support various kinds of signals including 4-20mA, RS485 and control pulse which are very convenient for user’s control process.
Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5%/1.0%

QTWG turbine gas flow meters are suitable for a wide range of markets, including natural gas, LPG and other gas industries. Q&T turbine gas meters could achieve high-precision custody transfer metering, the measurements can be automatically pressure and temperature compensated to obtain volumetric measurements in standard units.
Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

QTWG series gas turbine meters offer high quality natural gas measurement which could increase efficiency in gas transmission, distribution and industrial applications. Turbine gas meters are wIth built in temperature and pressure compensation ensure accurate measurment in standard conditions.

Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

liquid turbine flow meter is a new generation turbine flow meter which was designed with advanced flow technologies both home and aboard. The product possesses advantages of simple structure, light in weight, high accuracy, good repeatability, short response time, easy installation, etc. It could be used widely in measurement of closed pipe system for pure liquid that will not react with 1Cr18Ni9Ti, 2Cr13, Al2O3 and hard alloys.

QTWG series gas turbine flow meter is is designed to measure natural gas, LPG gas, other clean gases accurately. Turbine gas meters
have the characteristics of low pressure loss, high accuracy,anti vibration and widely range ratio etc. With the ability of increasinig efficiency in boiler/burner control, fuel-to-air ratio, and custody transfer applications.
Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

Turbine flow meters are mechanical meters that have a freely rotating turbine set in the path of a fluid stream. The flowing liquid or gas causes the turbine to spin upon its axis. The rate of spin will be proportional to the velocity of the flow. Turbine flow meters are simple and reliable.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART

QTWG series natural gas flow meter is used to measure gas flow, with the features of high accuracy, low-pressure drop. Wide turndown gas turbine flow meter is custody transfer approval flow meter, widely used in clean gas including natural gas, LPG gas etc.
Size:DN25-200mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Installation: Vertical or Horizontal
Accuracy:1.5% or 1.0%

turbine flowmeter is widely used in low flow rate and low viscosity Liquid measurement. Converting sensor signals into smart signal outputs through a microcomputer
processor design.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART

The precision turbine flow meter offers outstanding accuracy and reliability.
With rugged stainless steel body,the turbine flow meter is compatible with most chemicals and will stand up well to high pressure applications.With high pressure ANSI 150# RF flange connections.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART
LCD display

Sanitary turbine flow meters have stainless steel bodies and come standard with Tri-Clover fittings. Sanitary flow meter is suitable for measuring liquid without impurities. It can output pulse frequency signal. It is used to detect instantaneous flow and total integrated flow. Sanitary flow meter can be used in food, sport drink, liquor and other beverage industries, in preprocess applications.

QTWG natural gas turbine flow meters are are ideal flow measurement device for natural gas or other non-corrosive gases applications. Turbine gas meters with wide range ratio which could achieve different flow range measurements.
Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

Turbine flow meters are designed for industrial and laboratory measurement of water, solvents and other low viscosity fluids.turbine flow meters feature a 316 stainless steel body and a tungsten carbide bearing. They offer good accuracy and reliability with very little pressure drop. The standard turbine flow meters feature threaded end connections.

QTLL series gas roots flow meter is is a high-quality positive displacement roots-type gas meter which is available in an assortment of sizes and options. Based on the principle of volumetric measurement, rotary gas meter is used to accurately measure the gas flow through a closed pipeline.
Size:DN25-200mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Installation: Vertical or Horizontal
Accuracy:1.5% or 1.0%

Turbine flowmeter installation
Normally turbine flow meter has flange, thread, clamp-on connections, and the fluids direction should be the same as the arrow on the meter body. The liquid turbine flow sensor can be installed horizontally and vertically, and the fluid direction must be upward when installed vertically.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

Turbine flow meters are mechanical meters that have a freely rotating turbine set in the path of a fluid stream. The flowing liquid or gas causes the turbine to spin upon its axis. The rate of spin will be proportional to the velocity of the flow. Turbine flow meters are simple and reliable.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART

Gas turbine flow meter is a very stable measurement device, which is a good choice for custody transfer application for natural gas. Natural gas turbine flow meter could be widely used in gas measuring from Petroleum, Chemical,Electric power,Industrial boiler etc.In addition,QTWG series gas turbine flow meter also be used in Gas-fired,Gas pipeline network,city gas field etc.
Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5%/1.0%

Turbine flowmeter is widely used in the following measurement objects: petroleum, organic liquid, inorganic liquid, liquefied gas, natural gas, coal gas and cryogenic fluid.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART
LCD display

Turbine flowmeter is a kind of speed meter, which has the advantages of high precision, good repeatability, simple structure, high pressure resistance, wide measurement range, small size, light weight, small pressure loss, long life, simple operation, convenient maintenance, etc. It is used to measure the volume flow and cumulative flow of low-viscosity, non-corrosive, clean liquids in closed pipelines. Can be widely used in petroleum, chemical, metallurgy, organic liquid, inorganic liquid, food, medicine and other industries
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART