NPT thread thermal gas mass flow meter for air

Split display insert thermal gas mass flow meter is one kind of competitive gas flow meter for natrual gas industry
Easy installation, simple maintenance, two-way detection, anti-vibration
Flow measurement up to 24 points,and its suitable for low flow measurement ,so thermal gas mass flow meter can be used for leak detection

Q&T thermal gas mass flow meter can be divided into five sections for correction,this operation will make measuring more accurate
Line type accuracy is ¡À1.0%
Insertion type accuracy is ¡À1.5%

Thermal gas mas flow meters are measuring the mass flow or volume flow of gas,flow range can do 0.5Nm/s¡«100Nm/s. So this meter also can be used for gas leak detection.
Thermal flow sensor temp is always 30¡æ higher than the medium temperature (environment temperature), and the meter adopts method of constant differential temperature, therefore the meter don¡¯t need temperature and pressure compensation in principle.

Thermal flow meter measure gas mass flow in various processes and offer distinct advantages, such as repeatability, low maintenance, and operating over a wide flow range. Here we discuss the meter¡¯s fundamentals, the working principle of thermal mass flow measurement, and the two approaches to measuring heat dissipation.
Accuracy:
In-line type accuracy:¡À1.0%
Insertion type accuracy::¡À1.5%
Power supply:DC24V and AC220V
Output:4-20mA,Pulse,RS485

Thermal gas mass flow meter be adopted LCD converter and its most commonly used to measure the mass flow of clean gases, such as air, nitrogen, hydrogen, helium, ammonia, argon, and other industrial gases.
According to the connect,thermal gas mass flow meter have flange type,thread type,tri-clamp type,wafer type,inertion type etc.
Media:All gas except acetylene and humid gas
Measure range:1:100
Sesnsor working temperature:-20~220℃
Transmitter working temperature:-20~45℃
Output:4-20mA

Insertion type thermal flow meter which be used to measure the air flow velocity.
Air velocity thermal flow meter with widely flow range and flow ratio can reach 1:100.
Measuring tube dia. is ¦Õ12mm and ball valve is 1/2″ NPT
24VDC power supply its more safety for gas.

Thermal mass flow meters can have very high rangeability and reasonable accuracy for gases flowrate ,but can’t measure humity gases
Thermal flow meter is accurate, easy to install, no moving parts and best suitable solution for measuring and controlling compressed Air, oxygen, nitrogen, biogas, digester gases, ethane and natural gas flow. Heat dispersion (mass flow) technology to provide proportional mass flow measurement resulting in higher accuracy performance at a lower cost than orifice flow meter, Vortex flow meter and other gas flow measuring devices.

Thernal gas flow meter is one kind smart gas flow instrument, It can easily and accurately detect the mass flowrate of gas,specical for low flowrate.
Such as :Air, Nitrogen, Hydrogen, Oxygen, Chlorine, Natural gas, Flue gas and Other gases (except acetylene gas)
Thermal gas mass flow emter be widely used in the process control and gas flow measurement of petroleum, chemical industry, metallurgy, electric power, water treatment, papermaking, food, medicine, cement, textile and various production and scientific research institutions.
Media:All gas except acetylene and humid gas
Measure range:1:100
Sesnsor working temperature:-20~220℃
Transmitter working temperature:-20~45℃
Output:4-20mA
Accuracy:±1.0%~±2.5%
Probe material:SS316L
Power supply:24VDC ,220VAC
Response time:1S
Display:4 line digital

Thermal flow sensor temp is always 30¡æ higher than the medium temperature (environment temperature), and the meter adopts method of constant differential temperature, therefore the meter don¡¯t need temperature and pressure compensation in principle
Power supply:DC24V and AC220V
Output:4-20mA,Pulse,RS485
Body material:Standard SS304,and SS316 is optional
Velocity:0.1~100Nm/s
Media temperature:-40~+220¡æ

Thermal gas mass flow meter measure the mass flowrate of gases ,so thermal flow meter is often used in monitoring gas mass-related process.
When thermal gas flow meter measure the gases,the gases’ volume measurement is affected by pressure and temperature,while mass flowrate measurement is unaffected by changes in viscosity, density, temperature, or pressure.
Digital display
Stainless steel body
Anti-corrosion
Pressure up to 4.0Mpa
Dural power:24VDC,220VAC
4-20mA is Optical isolation

The thermal gas flowmeter is mainly used for measuring gas with low flow and the range could reach 1:100,which is btter than gas flowmeter on market and low flow could be measured,the min.flow velocity can reach 0.1Nm/s and Max. velocity reach 100Nm/s
Media:All gas except acetylene and humid gas
Measure range:1:100
Sesnsor working temperature:-20~220℃
Transmitter working temperature:-20~45℃
Output:4-20mA

Q&T thermal gas mass flow meter with DC4-20mA four-wire output,which is more convenient for remote reception.Support MODBUS RTU RS485 protocol,coordinating the receiving system to collect more data ans modify system
Velocity:0.1~100Nm/s
Media temperature:-40~+220¡æ
Size£º
Insertion type:DN32~DN4000
Flange type:DN10~DN300
Tri-clamp type :DN10~DN100
Thread type:DN10~DN100

Thermal flow meter is one kind of gas mass flow meter, can display mass flow rate and total mass flow
According to request, Q&T can do OEM ,such as display converter color,Display LOGO,Flow unit etc.
Output is 4-20mA,Pulse
Communication is RS485 or HART

Natural gas thermal mass flow meters measure the mass flowrate of fluids by measuring the heat conducted from a heated surface to the flowing fluid. Since a flowing fluid removes a known quantity of heat as it passes, the temperature difference between the heated sensor and the flow stream is directly proportional to the mass flow rate.
With RS485 or HART communication
Power supply:24VDC ,220VAC
Accuracy:¡À1.0%~¡À1.5%

Thermal flowmeters directly indicate the mass flow or normalized volume flow of gases without any additional pressure and temperature compensation. They have an impressively high accuracy, short response time and a very wide flow range with virtually no loss of accuracy even at the lowest flow rates
Mass flow
SS304 rod
Dual power:24VDC,220VAC
Min.Flow velocity:0.1Nm/s
Online installation

Insertion thermal gas mass flow meter with anti flush-out design for high pressure,more safety
When absolute pressure of measuring medium is higher than 5 times standard atmospheric pressure, or higher than the pressure of possible danger, should shut down or do reducing pressure to reach a safety pressure, and then do hot-tapped operation. If there are no conditions to do hot-tapped operation, should shut down to avoid dangers.

Intelligent thermal gas mass flow meter with DC4-20mA four-wire output,which is more converient for remote reception.Support MODBUS RTU RS485 protocol.
LCD display thermal gas flow meter is a meter that uses the principle of heat transfer to detect flow.
In-line type accuracy:¡À1.0%
Insertion type accuracy::¡À1.5%
Power supply:DC24V and AC220V
Output:4-20mA,Pulse,RS485

Thermal gas mass flowmeters directly indicate the mass flow or normalized volume flow of gases without any additional pressure and temperature compensation. They have an impressively high accuracy, short response time and a very wide flow range with virtually no loss of accuracy even at the lowest flow rates and the range could reach 1:100.
Volume flow /Mass flow
SUS304 body
MODBUS RTU RS485
0.1~100Nm/s
4 lines LCD
EX-PROOF

Thermal gas mass flow meter mainly measure various of gases ,special dry gases,but thermal gas mass flow meter can’t measure acetylene.
In many applications, the thermal properties of the fluid can be dependent upon fluid composition. In such applications, varying composition of the fluid during actual operation can affect the thermal flow measurement. Therefore, it is important for the thermal flow meter supplier to know the composition of the fluid so that the proper calibration factor can be used to determine the flow rate accurately
Widly flow range ratio:1:100
Display:4 line digital
With RS485 or HART communication
Power supply:24VDC ,220VAC
Accuracy:¡À1.0%~¡À1.5%

Thermal gas mass flow meter is one kind of precision instrument,ensuring the accuracy is important.
Q&T adopt the critical flow nozzle calibration device to calibrate each gas mass flow meter,the calibration device flow range can reach Min. 0.5m3/h and Max.10000 m3/h .
Nozzle calibration device more ensure the flow meters’ accuracy
Accuracy:
In-line type accuracy:¡À1.0%
Insertion type accuracy::¡À1.5%
Power supply:DC24V and AC220V
Output:4-20mA,Pulse,RS485
Body material:Standard SS304,and SS316 is optional

Thermal gas mass flow emter be widely used in the process control and gas flow measurement of petroleum, chemical industry, metallurgy, electric power, water treatment, papermaking, food, medicine, cement, textile and various production and scientific research institutions.
Natural gas thermal gas mass flow meter can reach 1.0% accuracy and has been calibrated by a third-party laboratory.
Dual power:24VDC,220VAC
Min.Flow velocity:0.1Nm/s
Online installation

The thermal gas flowmeter is mainly used for measuring gas with low flow and the range could reach 1:100,which is btter than gas flowmeter on market and low flow could be measured,the min.flow velocity can reach 0.1Nm/s and Max. velocity reach 100Nm/s
Media:All gas except acetylene and humid gas
Measure range:1:100
Sesnsor working temperature:-20~220℃
Transmitter working temperature:-20~45℃
Output:4-20mA
Accuracy:±1.0%~±2.5%
Probe material:SS316L
Power supply:24VDC ,220VAC
Response time:1S
Display:4 line digital

4-20mA ouput thermal gas mass flow meter is on kind flow meter for direct mass measurementt of Air,N2, CO2,Natrual gas ect.
Whenever low pressure loss is important in gas industry thermal mass flowmeters offer a real alternative to traditional measuring techniques.
Whatever for process control, consumption and supply monitoring, detecting leaks or monitoring distribution networks. Using insertion versions, it is also possible to measure gas flows in very large pipelines or in rectangular ducts.
Media:All gas except acetylene and humid gas
Measure range:1:100
Sesnsor working temperature:-20~220℃
Transmitter working temperature:-20~45℃
Output:4-20mA
Accuracy:±1.0%~±2.5%
Probe material:SS316L
Power supply:24VDC ,220VAC
Response time:1S
Display:4 line digital

Thermal gas flowmeter is mainly used for measuring gas with low flow and the range could reach 1:100,which is btter than gas flowmeter on market and low flow could be measured,the min.flow velocity can reach 0.1Nm/s and Max. velocity reach 100Nm/s
Volume flow /Mass flow

Thermal mass flow meter is precision instruments that can directly measure mass flow,such as industrial gases, compressed gas, and other gases.
Gas thermal mass flow meter body is be made by stainless steel and stainless steel is more durable and better air tightness.
DC4-20mA four-wire output
Mass flow unit
Dual power:24VDC,220VAC
Min.Flow veloctiy:0.1Nm/s
Output:4-20mA

Except for acetylene,thermal gas mass flowmeters can measure various of dry gas.
Such as Air, Natrual gas, N2, O2, CO2 etc.When measure the flammable and explosive gas,the flow meter need with ex-proof function.
24VDC will better and safety

Thermal gas mass flow meter with DC4-20mA four-wire output,which is more converient for remote reception.Support MODBUS RTU RS485 protocol,coording the receiving system to collect more data and modify system and Q&T brand thermal gas mass flow meter already got CE ,Ex-Proof certificates
Pressure:
Insertion type¡Ü1.6Mpa
Flange type ¡Ü4.0Mpa

As the flow meter final manufacturer,OEM and ODM are very normal ,such as Color,Material,Display,Output,Process Connect,Function etc.
Q&T brand thermal mass flowmeters are suitable for all industrial and test rig applications that demand quick and precise gas measurement. The flowmeters directly indicate the mass flow or normalized volume flow of gases without any additional pressure and temperature compensation. They have an impressively high accuracy, short response time and a very wide flow range with virtually no loss of accuracy even at the lowest flow rates.
DC4-20mA four-wire output
Flow unit:Nm3
SS304 rod
All gas except acetylene and humid gas
Measure range:1:100
Sesnsor working temperature:-20~220¡æ
Transmitter working temperature:-20~45¡æ

Insertion type thermal gas mass flow meter need to reserve 20mm mounting hole,which could be used to weld and fix the base,Inline type thermal gas mass flow meter could be min.size 10mm.
Easy installation and maintenance. If the conditions on site are permissible, the meter can achieve a hot-tapped installation and maintenance. (Special order of custom-made)
Output:4-20mA,Pulse,OCT
Communication:RS485
Transmitter working temperature:-10~70¡æ
Sensor wotking temperature:-30~150¡æ
Power supply:DC24V,AC220V

For the insertion type instrument, on the premise that both the measuring media and field environment are applicable for online dismantlement with non-stop operation, it is viable to have maintenance operation with non-stop operation relying on its special structure.
Velocity:0.1~100Nm/s
Media temperature:-40~+220¡æ
Size£º
Insertion type:DN32~DN4000
Flange type:DN10~DN300
Tri-clamp type :DN10~DN100
Thread type:DN10~DN100