Compressed air flowmeter remote version thermal gas flow meter

Q&T thermal gas mass flow meter with DC4-20mA four-wire output,which is more convenient for remote reception.Support MODBUS RTU RS485 protocol,coordinating the receiving system to collect more data ans modify system
Media:All gas except acetylene and humid gas
Measure range:1:100
Sesnsor working temperature:-20~220℃
Transmitter working temperature:-20~45℃
Output:4-20mA
Accuracy:±1.0%~±2.5%
Probe material:SS316L
Power supply:24VDC ,220VAC
Response time:1S
Display:4 line digital

Thermal gas mass flowmeter for natural gas
As one kind gas flow meter,thermal gas mass flow meter also can measure natural gas.
Compared to gas turbine flow meter,the thermal gas mass flow meter is cost-effective and have a wide measurement trundown ratio.

Q&T thermal gas mass flow meter can be divided into five sections for correction,this operation will make measuring more accurate
Line type accuracy is ¡À1.0%
Insertion type accuracy is ¡À1.5%
Media:All gas except acetylene and humid gas
Measure range:1:100
Sesnsor working temperature:-20~220℃
Transmitter working temperature:-20~45℃
Output:4-20mA
Accuracy:±1.0%~±2.5%
Probe material:SS316L

Thermal gas mass flow meter be adopted LCD converter and its most commonly used to measure the mass flow of clean gases, such as air, nitrogen, hydrogen, helium, ammonia, argon, and other industrial gases.
According to the connect,thermal gas mass flow meter have flange type,thread type,tri-clamp type,wafer type,inertion type etc.
Media:All gas except acetylene and humid gas
Measure range:1:100
Sesnsor working temperature:-20~220℃
Transmitter working temperature:-20~45℃
Output:4-20mA

Theemal flowmeters directly indicate the mass flow or normalized volume flow of gases without any additional pressure and temperature compensation. They have an impressively high accuracy, short response time and a very wide flow range with virtually no loss of accuracy even at the lowest flow rates.
Widely turndown ratio:100:1
Power supply:24VDC&220VAC
Response time:1S

Q&T gas mass flowmeter thermal gas mass flow meter is one of hot sale flow meter, This thermal flow meter feature is no moving parts, nearly unobstructed straight through flow path, require no temperature or pressure corrections and retain accuracy over a wide range of flow rates.
Widely turndown ratio:100:1
Power supply:24VDC&220VAC
Response time:1S

4-20mA ouput thermal gas mass flow meter is on kind flow meter for direct mass measurementt of Air,N2, CO2,Natrual gas ect.
Whenever low pressure loss is important in gas industry thermal mass flowmeters offer a real alternative to traditional measuring techniques.
Whatever for process control, consumption and supply monitoring, detecting leaks or monitoring distribution networks. Using insertion versions, it is also possible to measure gas flows in very large pipelines or in rectangular ducts.

Split display insert thermal gas mass flow meter is one kind of competitive gas flow meter for natrual gas industry
Easy installation, simple maintenance, two-way detection, anti-vibration
Flow measurement up to 24 points,and its suitable for low flow measurement ,so thermal gas mass flow meter can be used for leak detection

Thermal gas mass flowmeters are suitable for all industrial and test rig applications that demand quick and precise gas measurement. The flowmeters directly indicate the mass flow or normalized volume flow of gases without any additional pressure and temperature compensation. They have an impressively high accuracy, short response time and a very wide flow range with virtually no loss of accuracy even at the lowest flow rates.
Mass flow
SS304 rod
Dual power:24VDC,220VAC
Min.Flow velocity:0.1Nm/s
Online installation

Thermal mass flowmeters are suitable for all industrial and test rig applications that demand quick and precise gas measurement.
Thermal air mass flow meter be adopted the critical flow nozzle calibration device to calibrate each gas mass flow meter,the calibration device flow range can reach Min. 0.5m3/h and Max.10000 m3/h .
Widely turndown ratio:100:1
Power supply:24VDC&220VAC
Response time:1S

Thermal gas mass flow meter have many benefits -Wide turndown ratio,low pressure drop,application flexibility and gas mass flow rate measurement.This thermal flow meter feature is no moving parts, nearly unobstructed straight through flow path, require no temperature or pressure corrections and retain accuracy over a wide range of flow rates.
RS485 or HART communication
Power supply:24VDC ,220VAC
Accuracy:¡À1.0%~¡À1.5%

Insertion thermal gas mass flow meter with anti flush-out design for high pressure,more safety
When absolute pressure of measuring medium is higher than 5 times standard atmospheric pressure, or higher than the pressure of possible danger, should shut down or do reducing pressure to reach a safety pressure, and then do hot-tapped operation. If there are no conditions to do hot-tapped operation, should shut down to avoid dangers.

LCD display thermal gas flow meter is a meter that uses the principle of heat transfer to detect flow.
The thermal gas flow meter is available in high-performance pipeline type and insert type flow meter. Insert flow meter consist of a probe with sensing elements that are inserted into the pipe irrespective of pipe size. These are easy to install and more economical. Inline flow meters are connected to the pipe itself by the flanged or threaded connection. Inline meters are suitable for smaller diameter pipes.

The thermal gas flowmeter is mainly used for measuring gas with low flow and the range could reach 1:100,which is btter than gas flowmeter on market and low flow could be measured,the min.flow velocity can reach 0.1Nm/s and Max. velocity reach 100Nm/s
Media:All gas except acetylene and humid gas
Measure range:1:100
Sesnsor working temperature:-20~220℃
Transmitter working temperature:-20~45℃
Output:4-20mA

Q&T thermal gas mass flow meter with DC4-20mA four-wire output,which is more convenient for remote reception.Support MODBUS RTU RS485 protocol,coordinating the receiving system to collect more data ans modify system
Velocity:0.1~100Nm/s
Media temperature:-40~+220¡æ
Size£º
Insertion type:DN32~DN4000
Flange type:DN10~DN300
Tri-clamp type :DN10~DN100
Thread type:DN10~DN100

As the important gas flow meter,thermal gas flow meter is very popluar to measure various of dry gas.
This gas mass flow meters are be calibrated by sonic nozzle,current the snoic nozzle is more better clibration device for gas flow meter,and ensure the accuracy during calibrating
Pressure up to 4.0Mpa
Dural power:24VDC,220VAC
4-20mA is Optical isolation
Power supply:DC24V and AC220V
Output:4-20mA,Pulse,RS485
Body material:Standard SS304,and SS316 is optional

Thermal gas flowmeter is mainly used for measuring gas with low flow and the range could reach 1:100,which is btter than gas flowmeter on market and low flow could be measured,the min.flow velocity can reach 0.1Nm/s and Max. velocity reach 100Nm/s
Volume flow /Mass flow

Intelligent thermal gas mass flow meter with DC4-20mA four-wire output,which is more converient for remote reception.Support MODBUS RTU RS485 protocol.
LCD display thermal gas flow meter is a meter that uses the principle of heat transfer to detect flow.
In-line type accuracy:¡À1.0%
Insertion type accuracy::¡À1.5%
Power supply:DC24V and AC220V
Output:4-20mA,Pulse,RS485

Q&T gas mass thermal flow meters are be calibrated by gas venturi sonic nozzle calibration device,and ensure the thermal gas mass flowmeter accuracy can reach 1.0% and 1.5%.
When calibrate thermal flow meter,Q&T will choose four flow velocity points ,then calibrate 3 times each velocity point
Media:All gas except acetylene and humid gas
Measure range:1:100
Sesnsor working temperature:-20~220℃
Transmitter working temperature:-20~45℃
Output:4-20mA

Thermal mass flow meters measure the mass flowrate of fluids by measuring the heat conducted from a heated surface to the flowing fluid.Support MODBUS RTU RS485 protocol,coordinating the receiving system .
With RS485 or HART communication
Power supply:24VDC ,220VAC
Accuracy:¡À1.0%~¡À1.5%

Insertion type thermal gas mass flow meter need to reserve 20mm mounting hole,which could be used to weld and fix the base,Inline type thermal gas mass flow meter could be min.size 10mm.
Easy installation and maintenance. If the conditions on site are permissible, the meter can achieve a hot-tapped installation and maintenance. (Special order of custom-made)
Output:4-20mA,Pulse,OCT
Communication:RS485
Transmitter working temperature:-10~70¡æ
Sensor wotking temperature:-30~150¡æ
Power supply:DC24V,AC220V

Thermal flowmeters directly indicate the mass flow or normalized volume flow of gases without any additional pressure and temperature compensation. They have an impressively high accuracy, short response time and a very wide flow range with virtually no loss of accuracy even at the lowest flow rates
Mass flow
SS304 rod
Dual power:24VDC,220VAC
Min.Flow velocity:0.1Nm/s
Online installation

Thermal meters require a fully developed flow profile as a prerequisite for correct flow measurement.
When the gas is very humid or saturated with water (e. g. Bio Gas), the piping and flowmeter body should be insulated to prevent water droplets condensing on the measuring sensor.
DC4-20mA four-wire output
Mass flow unit
Dual power:24VDC,220VAC
Min.Flow veloctiy:0.1Nm/s
Output:4-20mA

As the flow meter final manufacturer,OEM and ODM are very normal ,such as Color,Material,Display,Output,Process Connect,Function etc.
Q&T brand thermal mass flowmeters are suitable for all industrial and test rig applications that demand quick and precise gas measurement. The flowmeters directly indicate the mass flow or normalized volume flow of gases without any additional pressure and temperature compensation. They have an impressively high accuracy, short response time and a very wide flow range with virtually no loss of accuracy even at the lowest flow rates.
DC4-20mA four-wire output
Flow unit:Nm3
SS304 rod
All gas except acetylene and humid gas
Measure range:1:100
Sesnsor working temperature:-20~220¡æ
Transmitter working temperature:-20~45¡æ

Gas mass flow meter also means thermal gas mass flow meter.
Thermal mass flow meters measure the mass flowrate of fluids by measuring the heat conducted from a heated surface to the flowing fluid. Since a flowing fluid removes a known quantity of heat as it passes, the temperature difference between the heated sensor and the flow stream is directly proportional to the mass flow rate.
Output:4-20mA
Accuracy:¡À1.0%~¡À1.5%
Probe material:SS316L
Power supply:24VDC ,220VAC
Response time:1S
Display:4 line digital

Q&T thermal gas mass flow meter with DC4-20mA four-wire output,which is more convenient for remote reception.Support MODBUS RTU RS485 protocol,coordinating the receiving system to collect more data ans modify system
Insertion rod diameter :
DN32~DN50 standard rod dia. 12mm ,14mm is optional
DN65~DN4000 standard rod dia.19mm,12mm and 14mm is optional

Thermal gas flowmeter is mainly used for measuring gas with low flow and the range could reach 1:100,which is btter than gas flowmeter on market and low flow could be measured,the min.flow velocity can reach 0.1Nm/s and Max. velocity reach 100Nm/s
Volume flow /Mass flow
Pressure:
Insertion type¡Ü1.6Mpa
Flange type ¡Ü4.0Mpa
Accuracy:
In-line type accuracy:¡À1.0%
Insertion type accuracy::¡À1.5%
Power supply:DC24V and AC220V

Wafer type thermalg gas mass flow meter is an instrument which measures fluid flow by means of heat conduction.
Straight pipe runs can be reduced by using dual-plate flow conditioning elements and installation is very simple with minimal pipe intrusions.
Body material is SS304
Large diameter, low flow rate, negligible pressure loss

Tri-clamp thermal gas mass flow meter body be adopted SS304 and probe is SS316
Tri-clamp connect is fast to install and it no moving parts, nearly unobstructed straight through flow path, require no temperature or pressure corrections and retain accuracy over a wide range of flow rates.
Tri-clamp thermal gas mass flow meter size from DN15~DN100mm

Thermal flow sensor temp is always 30¡æ higher than the medium temperature (environment temperature), and the meter adopts method of constant differential temperature, therefore the meter don¡¯t need temperature and pressure compensation in principle
Power supply:DC24V and AC220V
Output:4-20mA,Pulse,RS485
Body material:Standard SS304,and SS316 is optional
Velocity:0.1~100Nm/s
Media temperature:-40~+220¡æ