Good Quality High Accuracy Digital Diesel Oil Liquid Turbine Flow Meter

turbine flowmeter advantage
1.High accuracy, generally up to ¡À1%R, ¡À0.5%R, high accuracy up to 0.2%R
2.Good repeat-ability, short-term repeat-ability up to 0.05% ~ 0.2%, in the trade settlement is the preferred choice of flow meter.
3.Output of pulse frequency signal, suitable for totalizer and connection with PC; no zero shift and strong interference resist
4.High frequency signal(3~4KHz) can be obtained, the signal resolution is strong.
5.Wide range, medium and large diameter up to 1:20, small caliber 1:10.

turbine flowmeter hydrodynamic positioning of the low mass rotor provides wider rangeability and longer bearing life than that of conventional turbine flowmeters. Integral flow straightening tubes minimize the effects of upstream flow turbulence. The housing is made of non-magnetic materials. The rotor is made of magnetic or magnetized material. Bearings are chosen based on service fluid, cost, and accuracy considerations.

Turbine flow meter use the mechanical energy of the fluid to rotate a “pinwheel” (rotor) in the flow stream. Blades on the rotor are angled to transform energy from the flow stream into rotational energy. The rotor shaft spins on bearings.
diesel turbine flow meter is a new generation turbine flow meter which was designed with advanced flow technologies both home and aboard.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

Turbine Flowmeters are the optimum combination of useful range, corrosion resistance, and operating life for a particular application. A low mass rotor design allows for a rapid dynamic response which permits the turbine flowmeter to be used in pulsating flow applications.

turbine flow meter is a volumetric metering the meter consists of a rotor and bearing assembly Suspended on a shaft, which is mounted to a support device.
magnetic or modulated pick-off sensor is used to detect the passage of each rotor blade and generate a frequency output. The frequency output can be read directly with the end users electronics or further processed to convert to a linear analog flow Rate output.
Turbine flow meters are used to measure clean, dry gases and liquids such as hydrocarbons, chemicals, gases and vapors, fuels
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

QTWG series natural gas flow meters adopt import impeller material which could ensure high accuracy in working life. Turbine gas meters offer high quality measurement solution for varous kinds of clean gas which could increase working efficiency in gas transmission, distribution and industrial applications etc.
Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

QTWG series gas turbine flow meters adopt import impeller material which could ensure high accuracy in working life. Designed to perform on the high level of accuracy, turbine gas flow meters are ideal product for commercial and industrial uses. QTWG series gas turbine flow meters low pressure loss,high accuracy,low initiating flow,anti vibration and pulsation flow resistance,widelyrange ratio etc.

Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

QTWG Turbine gas meter volume measuring instruments for gaseous media and operate according to the displacement principle. They register the gas volume under working conditions. In order to correct the measured value to the standard volume, electronic volume correctors can be used.Turbine gas meters deliver high accuracy in gas flow measurements, which could highly inrease the efficiency in various custody transfer applications.

Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

Turbine flowmeters are widely used in petrochemicals, organic liquids, inorganic liquids, liquefied gases, natural gas and fluids at low to middle temperature .Now it is widely used which is next to orifice plate flow meter.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART

Gas turbine flow meter is a very stable measurement device, which is a good choice for custody transfer application for natural gas. Natural gas turbine flow meter could be widely used in gas measuring from Petroleum, Chemical,Electric power,Industrial boiler etc.In addition,QTWG series gas turbine flow meter also be used in Gas-fired,Gas pipeline network,city gas field etc.
Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5%/1.0%

Gas turbine flow meter is a new generation of flow measurement device for clean gas, including natural gas, LPG gas etc. Normally LPG gas flow meter need to be with temperature and pressure compensation so that to make sure high accuracy.
Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5%/1.0%

Turbine flow meters are used to measure clean, dry gases and liquids such as hydrocarbons, chemicals, gases and vapors, fuels and other types of liquids with lower viscosity, and for applications requiring highly accurate and precise measurements.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

The turbine flow meter is an ideal solution when high accuracy, compact size, fast response, and high tolerance to shock and vibration are critical requirements and suitable for wide range of viscosity medium including oil, gas, water and wastewater, chemical, gas utility, power, food and beverage£¬pharmaceutical, etc.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART

QTLL series gas roots flow meter is is a high-quality positive displacement roots-type gas meter which is available in an assortment of sizes and options. Based on the principle of volumetric measurement, rotary gas meter is used to accurately measure the gas flow through a closed pipeline.
Size:DN25-200mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Installation: Vertical or Horizontal
Accuracy:1.5% or 1.0%

QTWG Turbine gas meter is a popular device for gas-fired, gas pipeline network and city gas field etc. Gas roots flow meters are one of the high quality working performance meters for natural gas measurement, which could highly inrease the efficiency in various custody transfer applications.
Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

QTWG turbine gas flow meters are suitable for a wide range of markets, including natural gas, LPG and other gas industries. Turbine gas meter is a very stable measurement device which it could achieve high-precision custody transfer metering, the measurements can be automatically pressure and temperature compensated to obtain volumetric measurements in standard units.
Size:DN25-200mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Installation: Vertical or Horizontal
Accuracy:1.5% or 1.0%

QTWG series turbine gas meters with electronic totalizer and integrated temperature and pressure compensation. Turbine gas meters with built-in battery operation, with external power supply optional. With display of pressure, temperature, flowrate, totalizer etc.

Size:DN25-400mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Accuracy:1.5% or 1.0%

The Liquid Turbine Measuring Principle Is Used In A Wide Range Of Different Branches Of Industry, Chemicals, Petrochemicals, Oil And
Gas, Food, And ¨C No Less Importantly ¨C In Custody Transfer Applications. Liquid Turbine Flowmeters Can Measure Virtually All Fluids: Cleaning Agents, Fuels, Vegetable Oils, Solvents, Silicon Oils, Fruit Solutions, Vinegar, Alcohol
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

QTWG intelligent ex proof natural gas flow meter is widely used for the exact determination of gas quantities. Turbine gas flow meter is widely used in gas measuring from Petroleum, Chemical, Electric power,Industrial boiler etc, which could increase efficiency in boiler/burner control, fuel-to-air ratio, and custody transfer applications.
Size:DN25-200mm
Material:Aluminum alloy or stainless steel
Dual Power:3.6V battery powered+DC24V
Output:4-20mA,Pulse,RS485
Installation: Vertical or Horizontal
Accuracy:1.5% or 1.0%

diesel turbine flow meter is a new generation turbine flow meter which was designed with advanced flow technologies both home and aboard. The product possesses advantages of simple structure, light in weight, high accuracy, good repeatability, short response time, easy installation, etc. It could be used widely in measurement of closed pipe system for pure liquid that will not react with 1Cr18Ni9Ti, 2Cr13, Al2O3 and hard alloys

turbine flow meter is a volumetric metering the meter consists of a rotor and bearing assembly Suspended on a shaft, which is mounted to a support device.
This assembly is mounted inside a housing of a calibrated internal diameter. As fluid passes through the flow meter housing, the rotor will spin at a rate proportional to the volume of liquid passing through the housing. A magnetic or modulated pick-off sensor is used to detect the passage of each rotor blade and generate a frequency output. The frequency output can be read directly with the end users electronics or further processed to convert to a linear analog flow Rate output.

preprocess applications.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

Turbine flowmeters are flow measurement instruments which use axial fluid momentum to turn a multibladed rotor, the angular velocity of which is approximately proportional to the volume flowrate. With appropriate calibration and operation, turbine meters offer precise and highly repeatable measurement of throughput and flowrate.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

liquid turbine flowmeter is a kind of precision flow measuring instrument. It can be used to measure the flow and totality of liquid with the corresponding flow metering instrument. It has simple structure, light weight, high precision and complex. A new generation of turbine flowmeters with good characteristics, responsiveness, easy installation and maintenance. Widely used in metallurgy, chemical, petroleum, urban construction, environmental protection, food, metallurgy, water supply, paper and other fields, it is an ideal instrument for flow metering and energy saving. High-precision measurement of the volumetric flow of liquids such as water, tap water, diesel, gasoline and lower viscosity crude oil..
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

A turbine flow meter is used for volumetric total flow &/or flow rate measurement & has a relatively simple working principle. As fluid flows through the turbine meter, it impinges upon turbine blades that are free to rotate about an axis along the center line of the turbine housing. The angular (rotational) velocity of the turbine rotor is directly proportional to the fluid velocity flowing through the turbine. The resulting output is taken by an electrical pickoff(s) mounted on the flow meter body.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

Turbine Flowmeter has simple structure, high accuracy, good repetitiveness, fast response and
convenient maintenance. It is widely used for liquid without corrosion to stainless steel, Al2O3 or hard alloy, without fibre or particle and kinematic viscosity less than 50¡Á10-6m2/s.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART
LCD display

turbine flow meter is a kind of precision flowmeter, which can be used to measure the flow and total amount of liquid together with the corresponding flowmeter. When used together with the quantitative control instrument developed by our factory, it can carry out high precision quantitative control of liquid feeding. Widely used in petroleum, chemical, metallurgy, scientific research and other fields of measurement and control system. Turbine flow sensors equipped with sanitary joints can be used in the pharmaceutical industry.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

Turbine Flow Meter is a main type of Impeller Flowmeter also including the Anemoscope and Water meter.it is made up of Sensor and Conversion-Show. The Sensor reacts to the average velocity of fluid with multi-blades rotor so as to speculating the flow value and the accumulative flow value.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART

turbine flowmeter can be applied to alcohol, toluene, etc. which are not electrically conductive. And it can be used also in oil and gas, power plants, pharmaceutical and pulp & paper-making industry. However, it is recommended to not use for fluids containing sludge or highly viscous fluids. Also, it can be provided in flange type or screw (male or female) type while being able to cope with various piping conditions.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%/¡À0.2%;
OUTPUT: PULSE/4-20mA;
Digital Communication:RS485, MODBUS; HART

Works well with Low viscosity liquids. The turbine turns when the good passes through and a pulsed counter provides the flow total on a digital display.Works well with Low viscosity liquids. The turbine turns when the good passes through and a pulsed counter provides the flow total on a digital display.
Process Connection£ºThread/Flange/Clamp
Sensor Material£ºSS304, SS316L Optional
ACCURACY:¡À0.5%;
OUTPUT: PULSE+4-20mA;
Digital Communication:RS485, MODBUS; HART

liquid turbine flow meter, is a precision flow measuring instrument,that can be used to measure the flow and total volume of liquids. The structure is explosion-proof and can show the total flow, instantaneous flow and percentage of flow fullness. It is widely used in measurement and control systems in petroleum, chemical, metallurgical, scientific research and other fields. Sensors equipped with sanitary fittings can be used in the pharmaceutical industry.