High Accuracy liquid level measurement 4-20mA Ultrasonic Level Meter

This 4-20mA output PTFE Liquid Level Sensor Q&T Beer Milk level Meter is used to measure the water,beverage or chemical liquid level. This ultrasonic level transmitter has been widely used on food industry, sewage plants, channel, river level monitoring etc.

Specifications:
Measuring Range: liquid: 0.2-30 m
Process Connection: G2 Thread/ M95*2.0
Energy Transducer Material: ABS, PVC, PTFE
Temperature: -40~ 75 Deg C
With automatic Temperature compensation.
Process Pressure: ¡À 0.1MPa
Precision: 0.2% of actual range
Signal output: 4-20mA (Option:HART)
Power Supply: DC20V~32V ¡Ý30mA
Mode of Indication: 4 Digit LCD

The blind area of product measurement is in the range of 7-8CM, which is suitable
for the measurement of small storage tanks
The product has extremely high measurement accuracy and is suitable for
high-precision measurement

76-81 GHZ frequency modulation wave FMCW radar products (also called a millimeter wave radar), because it USES higher than Ku band radar frequency millimeter wave band, the remote target detection, strong smoke dust environment.

QTLM series Ultrasonic level meter is digital type non contact level measurement for liquid, solid etc.Ultrasonic level meter could meet most of the level measurement requirements. Material. It support various connections like thread or flange connection type which is much easier for user.
Level Range: 4m, 6m, 8m, 10m, 12m, 15m, 20m, 30m
Accuracy: 0.5%-1.0%
Resolution: 3mm or 0.1%
Display: LCD display
Analog Output: Two wire 4-20mA (250ohm Load)
Power Supply: DC24V
Environmental Temperature: Transmitter: -20 ~ + 60 degC
Sensor: -20 ~ + 80 degC
Working Pressure: Ambient pressure
Communication: HART

Ultrasonic fuel tank level sensor adopt ultrasonic technology is a good choice for level applications that require low cost, non-contact liquid slurry and solid level measurement. Especially for sewage treatment, paper pulp, urban water supply etc.
Ultrasonic level transmitter support 4-20mA two wire and HART communication, which is very convenient for customer’s application.
Range:4-30m
Output:4-20mA/HART
Connection:Thread/Flange
Power:DC24V
Accuracy:0.5%
Protection:IP65

As the China’s leading provider of ultrasonic level measurement technology, QTLM offers a wide selection of devices, from user-friendly and highly reliable transmitters to a broad portfolio of controllers and a broad range of transducers.QTLM ultrasonic level meter is a good choice for level applications that require low cost, non-contact liquid slurry and solid level measurement.
Level Range:4-30m
Sensor:ABS/PVC/PTFE
Output: 4-20mA/HART
Power:DC24V
Accuracy:0.5%

QTLM Series Ultrasonic level meter is a kind of non contact level measurement device which are widely used in liquid or solid application.One machine can handle various conditions.QTLM Liquid tank level sensor is made up of ABS probe or PTFE probe selectable, with acid and alkali resistance and safety installed in bad environment.

Level Range:4-30m
Sensor:ABS/PVC/PTFE
Output: 4-20mA/HART
Power:DC24V
Accuracy:0.5%

Ultrasonic level meter is a level measuring device with the features of non-contact, high reliability, cost-effective, easy to be installed and maintained.
Q&T ultrasonic level tank meter is widely used in liquid or solid application.
Level Range:4-30m
Accuracy:0.5%
Sensor:ABS/PVC/PTFE
Resolution:3mm or 0.1%
Output:Two wire 4-20mA/HART
Power:DC24V

QTLM Series Ultrasonic level meter is a kind of non contact level measurement device which are widely used in liquid or solid application.One machine can handle various conditions.QTLM Liquid tank level sensor is made up of ABS probe or PTFE probe selectable, with acid and alkali resistance and safety installed in bad environment.Especially for sewage treatment, paper pulp, urban water supply etc
Level Range:4-30m
Sensor:ABS/PVC/PTFE
Output: 4-20mA/HART
Power:DC24V
Accuracy:0.5%

QTLM 4-20mA ultrasonic level sensor is a kind of continuous measurement of fluids that do not contain foam, vapors, fumes or gases. Support analog and HART communication, which is widely used in water, fuel tank, food tank, solid level application. Ultrasonic level meters are with the ability to provide critical data of processes through PLC control device.
Range:4-30m
Application:Liquid / Solid
Sensor: ABS/PVC/PTFE
Output:4-20mA/HART
Power:DC24V
Accuracy:0.5%

Q&T Non Contact Ultrasonic Level Gauge has optional Output: 4-20 mA, relay and Hart etc; This ultrasonic liquid level transmitter can easily connect up to most systems. Ultrasonic level Sensor Material optional ABS, PVC, PTFE; Anti-corrosive with PTFE Probe.

Specifications:
Measuring Range: liquid: 0.2-30 m
Process Connection: G2 Thread/ M95*2.0
Energy Transducer Material: ABS, PVC, PTFE
Temperature: -40~ 75 Deg C
With automatic Temperature compensation.
Process Pressure: ¡À 0.1MPa
Precision: 0.2% of actual range
Signal output: 4-20mA (Option:HART)
Power Supply: DC20V~32V ¡Ý30mA
Mode of Indication: 4 Digit LCD

Ultrasonic level tank meter is made up of ABS or PTFE probe which is with acid and alkali resistance. QTLM ultrasonic level meter could be safety installed in complex environments. Support various different connection ways like thread or flange connection.
Range:4-30m
Application:Liquid / Solid
Sensor: ABS/PVC/PTFE
Output:4-20mA/HART
Power:DC24V
Accuracy:0.5%

Steam flowmeter is applicable for liquid or gas measurement,the calibration is different for vortex air flow meter and liquid vortex flow meter. Size: DN15-DN6000; Measured medium: liquid,gas,steam; Medium Temp: -40¡æ~250¡æ,-40¡æ~350¡æ,
Accuracy: ¡À1.0 % (Flange / wafer / thread / tri-clamp; ¡À1.5 % (Insertion type)
Specifications: DN100-2000 (Insertion),
Material: SS304(Standard),SS316(Optional) Signal Output: 4-20mA,Pulse Communication: RS485 MODBUS or HART

PTFE Liquid Level Sensor RS485 Sanitary Ultrasonic Water Tank Level Meter is a good choice for application such as Dam water level monitoring,River monitoring, Pool water level monitoring, Environmental water level monitoring; It has Multiple Output: 4-20 mA, relay and RS485 etc; easily connect up to most systems.

Specifications:
Measuring Range: liquid: 0.2-30 m
Process Connection: G2 Thread/ M95*2.0
Energy Transducer Material: ABS, PVC, PTFE
Temperature: -40~ 75 Deg C
With automatic Temperature compensation.
Process Pressure: ¡À 0.1MPa
Precision: 0.2% of actual range
Signal output: 4-20mA (Option:HART)
Power Supply: DC20V~32V ¡Ý30mA
Mode of Indication: 4 Digit LCD

Magnetic Level Gauges provides direct, high clarity indication of liquid level. Magnetic level gauge are now widely used in all industries as they avoid direct contact with indicator system;
Measuring range: 300¡«15000mm
Measurement accuracy: ¡À5mm or ¡À10mm
Working pressure: 1.0, 1.6, 2.5, 4.0, 6.4 ,10,16.0MPa
Working temperature: ¡Ü550¡æ
Medium viscosity: ¡Ü0.02Pa.S
Output signal: two-wire system 4¡«20mADC or HART protocol or four-wire system 485 digital output
Explosion-proof grade: Exdll CT6
Protection level: IP66

QTLM ultrasonic level sensor emits ultrasonic pulses in the direction of the medium,which support various connections like thread or flange connection type which is much easier for user.QTLM series Ultrasonic level transmitter have full-screen self-illumination,easy setting and debugging of liquid level measurement.
Level Range:4-30m
Sensor:ABS/PVC/PTFE
Output: 4-20mA/HART
Power:DC24V
Accuracy:0.5%

80G radar level meter is FMCW radar operating at 76-81 GHz, which has a maximum measuring range of 120m and a minimum blind zone of 8cm. It supports 4-wire and 2-wire applications. Higher operating frequency and shorter wavelength make it ideal for solid applications,

Q&T non-contact oil level Ultrasonic Level Gauge is microprocessor controlled digital level instrument, a good choice of Oil Diesel Fuel Liquid Level Meter. Ultrasonic pulses generated by the sensor (transducer) sent in the measurement, the surface acoustic wave after reflection by the liquid or receiving the same ultrasonic receiver transducer.

Specifications:
Measuring Range: liquid: 0.2-30 m
Process Connection: G2 Thread/ M95*2.0
Energy Transducer Material: ABS, PVC, PTFE
Temperature: -40~ 75 Deg C
With automatic Temperature compensation.
Process Pressure: ¡À 0.1MPa
Precision: 0.2% of actual range
Signal output: 4-20mA (Option:HART)
Power Supply: DC20V~32V ¡Ý30mA
Mode of Indication: 4 Digit LCD

Process pressure£º-0.1~0.5MPa
Measurement accuracy£º¡À1mm
Protection class£ºIP67
Explosion-proof grade£ºExib II CT6 Gb
Shell material£ºCast aluminum/stainless steel
Signal output£º4-20mA, HART (two-wire, four-wire), RS485 Modbus

Non contact ultrasonic level meter is easily configured by menu button and could give precision and accuracy for real-time measurement. Ultrasonic level gauge offer lowering operational costs and increasing productivity. Ultrasonic level meter is a good choice for process or control automation applications can be monitored via local display or remote PLC.
Range:4-30m
Application:Liquid / Solid
Sensor: ABS/PVC/PTFE
Output:4-20mA/HART
Power:DC24V
Accuracy:0.5%

Two wire Ultrasonic level meter with the feature of contactless and material independent, easy and flexible mounting. QTLM ultrasonic level sensor adopt temperature compensation, over voltage and over current protection, which could ensure safety use.
Range:4-30m
Application:Liquid / Solid
Sensor: ABS/PVC/PTFE
Output:4-20mA/HART
Power:DC24V
Accuracy:0.5%

Q&T PTFE Liquid Level Sensor PVDF Sensor ultrasonic level transmitter is a digital level meter with high- performance microprocessor to process signals; It meets the requirements of material level without the contact. It can be widely used for level measurement of municipal river, urban groundwater level, sewage treatment station, water works, etc.

Specifications:
Measuring Range: liquid: 0.2-30 m
Process Connection: G2 Thread/ M95*2.0
Energy Transducer Material: ABS, PVC, PTFE
Temperature: -40~ 75 Deg C
With automatic Temperature compensation.
Process Pressure: ¡À 0.1MPa
Precision: 0.2% of actual range
Signal output: 4-20mA (Option:HART)
Power Supply: DC20V~32V ¡Ý30mA
Mode of Indication: 4 Digit LCD

Non-contact ultrasonic liquid tank level sensor delivers reliable level measurement in condensing environments. It could be used for media in small, medium and large capacity tanks from 5meter to 30meters. Ultrasonic level gauge support continuous level measurement, switching and control.
Range:4-30m
Application:Liquid / Solid
Sensor: ABS/PVC/PTFE
Output:4-20mA/HART
Power:DC24V
Accuracy:0.5%

PTFE Liquid Level Sensor High accuracy Ultrasonic Level Meter is microprocessor controlled digital level instrument, a good choice of Oil Diesel Fuel Liquid Level Meter. Ultrasonic pulses generated by the sensor (transducer) sent in the measurement, the surface acoustic wave after reflection by the liquid or receiving the same ultrasonic receiver transducer.

Specifications:
Measuring Range: liquid: 0.2-30 m
Process Connection: G2 Thread/ M95*2.0
Energy Transducer Material: ABS, PVC, PTFE
Temperature: -40~ 75 Deg C
With automatic Temperature compensation.
Process Pressure: ¡À 0.1MPa
Precision: 0.2% of actual range
Signal output: 4-20mA (Option:HART)
Power Supply: DC20V~32V ¡Ý30mA
Mode of Indication: 4 Digit LCD

Q&T Ultrasonic level transmitters are widely used for water, waste water level measurement. As one of the leading manufacturer, Q&T focus in the ultrasonic level transmitter’s production, test, packing etc. To ensure safety in shipment, QTLM series ultrasonic level transmitters are packed in safety export cartons with well protection.

80G radar level meter is FMCW radar operating at 76-81 GHz, which has a maximum measuring range of 120m and a minimum blind zone of 8cm. It supports 4-wire and 2-wire applications. Higher operating frequency and shorter wavelength make it ideal for solid applications,

humidity: ¡Ü95%RH
Enclosure: Aluminum alloy, stainless steel
Antenna type: Lens antenna/anti-corrosive antenna / flange isolated by quartz
Process temperature: -40~85¡æ; -40~200¡æ;
Process pressure: -0.1~2MPa
Product Size: ?100*270mm
Cable entry: M20*1.5
Protection class: IP67
Explosion-proof grade: ExdiaIICT6
Installation method: Thread or flange

Milk Level 4-20mA Non Contact Sanitary Ultrasonic Level Gauge is a High accuracy OEM available wastewater Level meter, top quality 4-20mA output and optional Hart Communication. This sanitary ultrasonic level transmitter is widely used on chemical tank, food industry milk level, water level etc.

Specifications:
Measuring Range: liquid: 0.2-30 m
Process Connection: G2 Thread/ M95*2.0
Energy Transducer Material: ABS, PVC, PTFE
Temperature: -40~ 75 Deg C
With automatic Temperature compensation.
Process Pressure: ¡À 0.1MPa
Precision: 0.2% of actual range
Signal output: 4-20mA (Option:HART)
Power Supply: DC20V~32V ¡Ý30mA
Mode of Indication: 4 Digit LCD

Ultrasonic level meter is a kind of non contact level measurement device which adopt Intellectual signal treatment technology. QTLM water tank level meter guarantee that the meter meets various kinds of operating occasion. Especially for waste water treatment, paper pulp, urban water supply etc.
Range:4-30m
Application:Liquid / Solid
Sensor: ABS/PVC/PTFE
Output:4-20mA/HART
Power:DC24V
Accuracy:0.5%

Ultrasonic level transmitter is a kind of continuous level measurement device. Widely used for liquid, slurry and solid level tank, with the feature of Non-contact and maintenance-free. Ultrasonic level gauge adopt temperature compensation technology which could make level measurement more accurate and stable.
Range:4-30m
Application:Liquid / Solid
Sensor: ABS/PVC/PTFE
Output:4-20mA/HART
Power:DC24V
Accuracy:0.5%