open channel flow meter wastewater open channel measurement flow system

Clamp flow meter fixed sewage ultrasonic flowmeter cutting required. The user simply clamp on the flow sensor to the pipe surface. Clamp flow meter fixed sewage ultrasonic flowmeter can then detect the flow through ultrasonic waves, and then automatically calculate the flow rate value, flow accumulator, etc. No pipe cutting means no damage to the pipe. So as long as the pipes are in good condition, the installation on the flowmeter will not provide the possibility of leakage. Sensor: Clamp-on/External Principle: transmit time Size: DN15mm-DN6000mm Measuring medium: Liquid 3.6V Battery-powered

Ultrasonic Flow meter for applications in clean water and in low conductivity media. Operating principle based on transit time measurement.
High Isolation voltage,Strong anti-interference,Suppress voltage noise,Good isolation performance
Inline ultrasonic flow meter collect temperature signal and accuracy reach 0.001¡æ
When using inline ultrasonic flow meter to measure,allowing pipe with liner
Szie:DN15~DN6000
Accuracy:¡À1.0 %
Viscosity:0.1~¡À10m/s
Output:4~20mA,Pulse,OCT,RS485
Power supply:DC24V and AC220V
Connection way:Flange type

Sincerity Ultrasonic Flow Meter Clamp Wall Mount Water Flow Sensor Ultrassonic Flow Meter For Liquid is an ultrasonic flowmeter used to measure the flow rate of liquids in closed pipes. The transducer is a non-contact, clamp-on type, which will provide the benefits of contamination-free operation and ease of installation. The transit time flowmeter employs two transducers, which act as ultrasonic transmitters and receivers. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

Flange ultrasonic flow meter could be manufactured from 50mm~700mm and mainly be used to measure the flow and heat of clean liquid which don’t contain large concentration of suspended particles or gas.

Inline ultrasonic flow meter could connect temperature sensor to become one calorimeter and widely
be used in Process control, Production measurement, Trade settlement and is suitable for continuously measuring flow and heat of clean and uniform liquids without large concentration suspended particles or gases industrial environment¡£
Support single channel and multi-channel at the same time,when one of channel is abnormal or not connected,it can automatically switch to single channel to working .

QTDS-100H Handheld ultrasonic Flowmeter Portable Water Flow meter use ultrasonic technology to measure the velocity of the liquid. Ultrasonic meters are avaiable as clamp-on solutions. Non pipe cutting, this ultrasonic flow meters can display velocity and accumulated flow. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Medium: clean liquids,pure water Built-in rechargeable battery 3.6V Housing Material: ABS

QT621 Portable ultrasonic flow meter applicable in all areas such as drinking water and sewerage industry, power plants,producing industry, food industry and many more. Portable ultrasonic water flow meter mainly consists of two parts, transmitter and transducer. QT621 ultrasonic flow meter support quickly verify the flow reading of another meter and to data log flow system values over an extended time period.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

Ultrasonic flow meter is suitable for continuously measuring flow and heat of clean and uniform liquids without large concentration suspended particles or gases industrial environment
Support single channel and multi-channel at the same time,when one of channel is abnormal or not connected,it can automatically switch to single channel to working .
Output:4-20mA,Pulse,OCT
Communication:RS485
Transmitter working temperature:-10~70¡æ
Sensor wotking temperature:-30~150¡æ
Power supply:DC24V,AC220V
Memory function

QT621 Portable ultrasonic flow meter could be widely used from simple water flow measurements to energy flow monitoring and automated process control. applications. QT621 ultrasonic flow meter uses clamp-on transducers that are mounted externally on the surface of the pipe and which generate pulses that pass through the pipe wall. Portable ultrasonic flow meter support quickly verify the flow reading of another meter and to data log flow system values over an extended time period.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

wall-mounted digital display industrial ultrasonic flow meter sea water ultrasonic flowmeter consists of two parts: a transmitter unit and a transducer. Magnetic external clamps on the sensor are easy to install and connect to metal tubing for continuous flow measurement. It is especially suitable for on-site flow measurement of various pressure requirements. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

New Version Protable Ultrasonic Water Flowmeter Price For Sale,Ultrasonic Flow Meter is a portable liquid flow measurement device with a sensor. New Version Protable Ultrasonic Water Flowmeter Price For Sale,Ultrasonic Flow Meter adopt transit-time ultrasonic measurement technology for superior accuracy and ease of installation and installation. This easy-to-use flowmeter comes in a rugged, waterproof carrying case for easy transport of the display, sensor, and cables between measurement locations. High accuracy +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

Ultrasonic Irrigation Open channel flow meter is for measuring water flow rates in irrigation channels, streams, and storm water systems. Open Channel Flow Meter can be used for continuous measuring of municipal rain-water, wastewater, sewage discharge and irrigation water pipelines.We have both transit-time ultrasonic open channel flow meter and doppler type ultrasonic open channel flow meter.

Specifications:
Analogue?Output: 4-20mA,?corresponding?to?instantaneous?flow
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS?-RTU?standard?protocol
Ambient?Temperature: -40 ~70 Degree C
Measure?Cycle: 1?second?(selectable?2?seconds?)
Power?Supply: DC24V?(+5%)?0.2A;?AC220V?(+20%)?0.1A?;Optional?DC12V

QT621 portable type ultrasonic flow meter is widely applied in oil industry, water treatment, pure water, chemical and etc.
Portable ultrasonic flow meter transmitter configurable for flow and thermal energy measurement. QT621 portable ultrasonic flow meter support quickly verify the flow reading of another meter and to data log flow system values over an extended time period.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

Fixed type ultrasonic clamp on flow meter adopts the self-development measurement technology.This measurement technique is a faster and more accurate process time measurement algorithm. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring single clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

The structure of 3.6V Waste Water Portable Handheld Ultrasonic Flow Meter is mainly divided into ultrasonic flow unit, flow transducer and information processing circuit, flow display. First, the ultrasonic signal generator is used to send the signal, the sensor receives the signal, and the time difference is obtained. The ultrasonic information is processed according to the information processing circuit, and the flow is transmitted to the display screen in the form of an electrical signal, and the result is displayed Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Medium: clean liquids,pure water Built-in rechargeable battery 3.6V Measurment unit: Meter, Feet,Cubic Meter.

Inline ultrasonic flow meter support single channel and multi-channel at the same time,when one of channel is abnormal or not connected,it can automatically switch to single channel to working
Ultrasonic flow measurement according to the ¡°differential transit time¡± method: This method uses two sensors, set opposite each other in the measuring tube. Each sensor can alternately transmit and receive ultrasonic signals, while simultaneously measuring the signal transit time.
Output:4~20mA,Pulse,OCT,RS485
Body material:Standard carbon steel,SS304 and SS316 are optional
Power supply:DC24V and AC220V
Connection way:Flange type
Media temperature :-30~+150¡æ

RS232 3.6V Lithium Battery Digital Water Handheld Ultrasonic Flow Meter is a non-contact instrument, which can measure the flow of medium with large diameter and can also be used for the measurement of medium that is not easy to contact and observe. Digital Water Handheld Ultrasonic Flow Meter measurement accuracy is very high, and it is hardly disturbed by various parameters of the measured medium.
Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Medium: clean liquids,pure water Built-in rechargeable battery 3.6V Communication: RS232

Our open channel flow meter display the level, flow rate, accumulate flow at the same time; This ultrasonic water flow meter has Analogue Output: 4-20mA, corresponding to instantaneous flow.
Display: Backlight LCD
The maximum of Accumulative Flow: 9999999.9 m3/h
Accuracy of Change in Level: 1mm or 0.2% of full span (whichever is greater)
Resolution: 1mm
Analogue Output: 4-20mA, corresponding to instantaneous flow
Relays Output: Standard 2 relay outputs(Optional up to 6 relays)
Serial Communication: RS485, MODBUS -RTU standard protocol
Ambient Temperature: -40 ~70 Degree C
Power Supply: DC24V (+5%) 0.2A; AC220V (+20%) 0.1A ;Optional DC12V

QT621 portable type ultrasonic clamp on flow meters use clamp-on transducers that are mounted externally on the surface of the pipe and which generate pulses that pass through the pipe wall.
Portable ultrasonic flow meters can be easily moved and installed in different pipes and convenient to carry site to site, which is very convenient for users to monitor the data.

Size: 1¡å~48¡å(25mm~1200mm)
Flow Range:¡À0.01 m/s~ ¡À12 m/s
Accuracy: ¡À1%
Repeatability: 0.2%
Output: 4-20mA, RS485
Power supply: Internal lithium 3000mAh
Transducer: IP68

This open Channel flow meter can be used for continuous measuring of municipal rain-water, wastewater, sewage discharge and irrigation water pipelines. This Open Channel flow meter measures level, flow rate and total volume of water flowing through weirs, flumes, and channels etc.

Specifications:
Display: Backlight?LCD
Flow?Rate?Range: 0.0000~99999L/S?or?m3/h
The?maximum?of Accumulative Flow: 9999999.9?m3/h
Accuracy?of?Change in Level: 1mm?or?0.2%?of?full?span?(whichever?is?greater)
Resolution: 1mm
Analogue?Output: 4-20mA,?corresponding?to?instantaneous?flow
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS?-RTU?standard?protocol

Inline ultrasonic flow meter support single channel and multi-channel at the same time,when one of channel is abnormal or not connected,it can automatically switch to single channel to working
Ultrasonic flow measurement according to the ¡°differential transit time¡± method: This method uses two sensors, set opposite each other in the measuring tube. Each sensor can alternately transmit and receive ultrasonic signals, while simultaneously measuring the signal transit time.
Input:Two-wire PT1000
Output:4-20mA,Pulse,OCT
Communication:RS485
Szie:DN15~DN6000
Accuracy:¡À1.0 %
Viscosity:0.1~¡À10m/s

The PLCM is an economical ultrasonic flowmeter specifically designed for open channel. Compared with other ultrasonic flow meters on the market, it has the characteristics of high reaction rate, low power consumption and high certainty. At the same time, with non-contact level sensor, it also have the feature of installation simple easy to use, non need water supply shutdown etc.

Specifications:
Display: Backlight?LCD
Flow?Rate?Range: 0.0000~99999L/S?or?m3/h
The?maximum?of Accumulative Flow: 9999999.9?m3/h
Accuracy?of?Change in Level: 1mm?or?0.2%?of?full?span?(whichever?is?greater)
Resolution: 1mm
Analogue?Output: 4-20mA,?corresponding?to?instantaneous?flow
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS?-RTU?standard?protocol

DN80 pipe ultrasonic flowmeter water liquid ultrasonic clamp on type is an ultrasonic flowmeter used to measure the flow rate of liquids in closed pipes. The transducer is clamp-on type, which will provide the benefits of contamination-free operation and ease of installation. The transit time flowmeter includes two transducers, which act as ultrasonic transmitters and receivers. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

For the Open Channel Water Meters, the level sensor is mounted on the top of the flume, and ultrasonic wave is transmitted by the probe to the surface of the monitored material. Instead of using mass or volumetric data to determine the rate of flow of a substance, open channel flow meters monitor the relationship between the depth of the liquid and the flow rate.Open Channel Flow Meter can be used for continuous measurement of municipal rainwater, wastewater, sewage discharge and irrigation water pipelines.

Specifications:
Sensor?Level?Range: 0-4.0m; other?level?range?also?available
Blind?zone: 0.20m
Temperature?Compensation: Integral?in?probe
Pressure?Rating: 0.2MPa
Beam?Angle: 8*?(3db)
Cable?Length: 10m?standard?(can?be?extended?to?1000m)
Sensor?Material: ABS,?PVC?or?PTFE?(optional)
Sensor?Protection Class: IP68

QTDS-100F wall mounted ultrasonic water flowmeter sensor heat meter adopts the self-development measurement technology.This measurement technique is a faster and more accurate process time measurement algorithm. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring single clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

Sewage and rainwater are often transported to the treatment plant in open collection channels or flumes.This open Channel flow meter is good for this application, it can be used for continuous measuring of municipal rain-water, wastewater, sewage discharge and irrigation water pipelines.

Specifications:
Display: Backlight?LCD
Flow?Rate?Range: 0.0000~99999L/S?or?m3/h
The?maximum?of Accumulative Flow: 9999999.9?m3/h
Accuracy?of?Change in Level: 1mm?or?0.2%?of?full?span?(whichever?is?greater)
Resolution: 1mm
Analogue?Output: 4-20mA,?corresponding?to?instantaneous?flow
Relays?Output: Standard?2?relay?outputs(Optional?up?to?6?relays)
Serial?Communication: RS485,?MODBUS?-RTU?standard?protocol

Pipeline ultraosnic flow meter directly contact the liquid and make the measuring accuracy better than clamp on ultrasonic flowmeter.And installation easy,don’t need calculate the sensor installation distance and cover the coupling agent in the pipe,so this meter can collect the signal very well.
Accuracy:¡À1.0 %
Viscosity:0.1~¡À10m/s
Output:4~20mA,Pulse,OCT,RS485
Body material:Standard carbon steel,SS304 and SS316 are optional

Portable clamp on ultrasonic flowmeter Water flow meter price handheld water flow meter for pipe handheld ultrasonic flowmeter is a portable liquid flow measurement device with a sensor. Hot sales portable ultrasonic flowmeter handheld water flow meter adopt transit-time ultrasonic measurement technology for superior accuracy and ease of installation and installation. This easy-to-use flowmeter comes in a rugged, waterproof carrying case for easy transport of the display, sensor, and cables between measurement locations. High accuracy +/-1.0% of FS Transducer temperature: -30~90¡ãC/-30¡ãC~160¡ãC Measuring clean liquids Battery-powered,for 12 hours Communication: RS232

Fixed type clamp on flowmeter with RS485 Modbus flow meter is an ultrasonic flowmeter used to measure the flow rate of liquids in closed pipes. The transducer is a non-contact, clamp-on type, which will provide the benefits of contamination-free operation and ease of installation. The transit time flowmeter employs two transducers, which act as ultrasonic transmitters and receivers. Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Measuring clean liquids Power supply: 24VDC/85VAC-2265AC Communication: RS485

Handheld ultrasonic water flowmeter for liquid is mainly divided into ultrasonic flow unit, flow transducer and information processing circuit, flow display. First, the ultrasonic signal generator is used to send the signal, the sensor receives the signal, and the time difference is obtained. The ultrasonic information is processed according to the information processing circuit, and the flow is transmitted to the display screen in the form of an electrical signal, and the result is displayed Accuracy: +/-1.0% of FS Wide range: DN15mm-DN6000mm Medium: clean liquids,pure water Built-in rechargeable battery 3.6V Measurment unit: Meter, Feet,Cubic Meter.