Q&T thermal gas mass flow meter mass flowmeter

Thermal flow meter measure gas mass flow in various processes and offer distinct advantages, such as repeatability, low maintenance, and operating over a wide flow range. Here we discuss the meter¡¯s fundamentals, the working principle of thermal mass flow measurement, and the two approaches to measuring heat dissipation.
Accuracy:
In-line type accuracy:¡À1.0%
Insertion type accuracy::¡À1.5%
Power supply:DC24V and AC220V
Output:4-20mA,Pulse,RS485

Q&T gas mass thermal flow meters are be calibrated by gas venturi sonic nozzle calibration device,and ensure the thermal gas mass flowmeter accuracy can reach 1.0% and 1.5%.
When calibrate thermal flow meter,Q&T will choose four flow velocity points ,then calibrate 3 times each velocity point
Media:All gas except acetylene and humid gas
Measure range:1:100
Sesnsor working temperature:-20~220℃
Transmitter working temperature:-20~45℃
Output:4-20mA

Wafer type thermalg gas mass flow meter is an instrument which measures fluid flow by means of heat conduction.
Straight pipe runs can be reduced by using dual-plate flow conditioning elements and installation is very simple with minimal pipe intrusions.
Body material is SS304
Large diameter, low flow rate, negligible pressure loss

Thermal gas mass flow meter measure the mass flowrate of gases ,so thermal flow meter is often used in monitoring gas mass-related process.
When thermal gas flow meter measure the gases,the gases’ volume measurement is affected by pressure and temperature,while mass flowrate measurement is unaffected by changes in viscosity, density, temperature, or pressure.
Digital display
Stainless steel body
Anti-corrosion
Pressure up to 4.0Mpa
Dural power:24VDC,220VAC
4-20mA is Optical isolation

Thermal dry gas flow meter is mainly used in air and gas flow measurement. The meters have flange type,wafer type,thread type,tri-clamp type;
Thermal gas mass flow meter consist of a transmitter and probe with temperature sensors (RTDS) located in the pins at the bottom of the probe. One sensor measures the process temperature and the other sensor is heated to a specific temperature above this. As the flow rate increases, heat gets taken away from the heated sensor in the form of convective heat transfer.
Media temperature:-40~+220¡æ

Size£º
Insertion type:DN32~DN4000
Flange type:DN10~DN300
Tri-clamp type :DN10~DN100
Thread type:DN10~DN100

Accuracy:
In-line type accuracy:¡À1.0%
Insertion type accuracy::¡À1.5%

As the flow meter final manufacturer,OEM and ODM are very normal ,such as Color,Material,Display,Output,Process Connect,Function etc.
Q&T brand thermal mass flowmeters are suitable for all industrial and test rig applications that demand quick and precise gas measurement. The flowmeters directly indicate the mass flow or normalized volume flow of gases without any additional pressure and temperature compensation. They have an impressively high accuracy, short response time and a very wide flow range with virtually no loss of accuracy even at the lowest flow rates.
DC4-20mA four-wire output
Flow unit:Nm3
SS304 rod
All gas except acetylene and humid gas
Measure range:1:100
Sesnsor working temperature:-20~220¡æ
Transmitter working temperature:-20~45¡æ

Thermal flow sensor temp is always 30¡æ higher than the medium temperature (environment temperature), and the meter adopts method of constant differential temperature, therefore the meter don¡¯t need temperature and pressure compensation in principle
Power supply:DC24V and AC220V
Output:4-20mA,Pulse,RS485
Body material:Standard SS304,and SS316 is optional
Velocity:0.1~100Nm/s
Media temperature:-40~+220¡æ

Thermal gas mass flowmeters directly indicate the mass flow or normalized volume flow of gases without any additional pressure and temperature compensation. They have an impressively high accuracy, short response time and a very wide flow range with virtually no loss of accuracy even at the lowest flow rates and the range could reach 1:100.
Volume flow /Mass flow
SUS304 body
MODBUS RTU RS485
0.1~100Nm/s
4 lines LCD
EX-PROOF

Thermal gas air flow meter is according the principle of constant temperature differential method is adopted for this instrument to measure the gas mass flow accurately, featured by small volume, high degree of digitalization, convenient installation and accurate measurement
Thermal gas mass flow meter have many benefits -Wide turndown ratio,low pressure drop,application flexibility and gas mass flow rate measurement.
DC4-20mA four-wire output
Mass flow unit
SS304 rod
Dual power:24VDC,220VAC
Min.Flow veloctiy:0.1Nm/s
Output:4-20mA

Thermal gas mass flowmeter have an impressively high accuracy, short response time and a very wide flow range with virtually no loss of accuracy even at the lowest flow rates.It is designed on the basis of thermal dispersion, and adopts method of constant differential temperature to measuring gas flow. It has advantages of small size, easy installation, high reliability and high accuracy, etc.
Media temperature:-40~+220¡æ
Size£º
Insertion type:DN32~DN4000
Flange type:DN10~DN300
Tri-clamp type :DN10~DN100
Thread type:DN10~DN100

Pulse output thermal gas mass flowmeters is one kind of instrument that measures the gas mass flowrate.
Thermal gas flow meter can be divided into inline type and isert type according to the instructure.
With RS485 or HART communication
Power supply:24VDC ,220VAC
Accuracy:¡À1.0%~¡À1.5%

Q&T adopt the critical flow nozzle calibration device to calibrate each gas mass flow meter,the calibration device flow range can reach Min. 0.5m3/h and Max.10000 m3/h .
Nozzle calibration device more ensure the flow meters’ accuracy
Accuracy:
In-line type accuracy:¡À1.0%
Insertion type accuracy::¡À1.5%
Power supply:DC24V and AC220V

Sometimes thermal gas mass flow meter be used to measure the dangerous gas,such as Natural gas,H2,O2 etc.So the thermal flow meter need with Ex-proof function.
Except above gas,mass flow meter also can measure N2,Ar,Air,CO2 etc
Flow measurement up to 24 points
Correction of output analog quantity Multipoint nonlinear curve correction
Flow and temperature detection at the same time, switch display
Digital LCD display
Stainless steel body
Output:4-20mA,Pulse,RS485
Accuracy:
In-line type accuracy:¡À1.0%
Insertion type accuracy::¡À1.5%

Intelligent thermal gas mass flow meter with DC4-20mA four-wire output,which is more converient for remote reception.Support MODBUS RTU RS485 protocol.
LCD display thermal gas flow meter is a meter that uses the principle of heat transfer to detect flow.
In-line type accuracy:¡À1.0%
Insertion type accuracy::¡À1.5%
Power supply:DC24V and AC220V
Output:4-20mA,Pulse,RS485

Thermal meters require a fully developed flow profile as a prerequisite for correct flow measurement.
When the gas is very humid or saturated with water (e. g. Bio Gas), the piping and flowmeter body should be insulated to prevent water droplets condensing on the measuring sensor.
DC4-20mA four-wire output
Mass flow unit
Dual power:24VDC,220VAC
Min.Flow veloctiy:0.1Nm/s
Output:4-20mA

Thermal gas flowmeter is mainly used for measuring gas with low flow and the range could reach 1:100,which is btter than gas flowmeter on market and low flow could be measured,the min.flow velocity can reach 0.1Nm/s and Max. velocity reach 100Nm/s
Volume flow /Mass flow

Except for acetylene,thermal gas mass flowmeters can measure various of dry gas.
Such as Air, Natrual gas, N2, O2, CO2 etc.When measure the flammable and explosive gas,the flow meter need with ex-proof function.
24VDC will better and safety

Thermal gas mass flow meter is one kind of precision instrument,ensuring the accuracy is important.
Q&T adopt the critical flow nozzle calibration device to calibrate each gas mass flow meter,the calibration device flow range can reach Min. 0.5m3/h and Max.10000 m3/h .
Nozzle calibration device more ensure the flow meters’ accuracy
Accuracy:
In-line type accuracy:¡À1.0%
Insertion type accuracy::¡À1.5%
Power supply:DC24V and AC220V
Output:4-20mA,Pulse,RS485
Body material:Standard SS304,and SS316 is optional

For the insertion type instrument, on the premise that both the measuring media and field environment are applicable for online dismantlement with non-stop operation, it is viable to have maintenance operation with non-stop operation relying on its special structure.
Velocity:0.1~100Nm/s
Media temperature:-40~+220¡æ
Size£º
Insertion type:DN32~DN4000
Flange type:DN10~DN300
Tri-clamp type :DN10~DN100
Thread type:DN10~DN100

4-20mA ouput thermal gas mass flow meter is on kind flow meter for direct mass measurementt of Air,N2, CO2,Natrual gas ect.
Whenever low pressure loss is important in gas industry thermal mass flowmeters offer a real alternative to traditional measuring techniques.
Whatever for process control, consumption and supply monitoring, detecting leaks or monitoring distribution networks. Using insertion versions, it is also possible to measure gas flows in very large pipelines or in rectangular ducts.
Media:All gas except acetylene and humid gas
Measure range:1:100
Sesnsor working temperature:-20~220℃
Transmitter working temperature:-20~45℃
Output:4-20mA
Accuracy:±1.0%~±2.5%
Probe material:SS316L
Power supply:24VDC ,220VAC
Response time:1S
Display:4 line digital

Thermal gas mass flow meter with DC4-20mA four-wire output,which is more converient for remote reception.Support MODBUS RTU RS485 protocol,coording the receiving system to collect more data and modify system and Q&T brand thermal gas mass flow meter already got CE ,Ex-Proof certificates
Pressure:
Insertion type¡Ü1.6Mpa
Flange type ¡Ü4.0Mpa

Thermal gas mass flow meter can measure the flow velocity,so its also named thermal gas velocity meters which maily measure the velocity of air.
Whenever low pressure loss is important in gas industry thermal mass flowmeters offer a real alternative to traditional measuring techniques.
Flow range:1:100
Pressure up to 4.0Mpa
4-20mA is Optical isolation
Power supply:24VDC&220VAC
Response time:1S

Thermal flow meter measure gas mass flow in various processes and offer distinct advantages, such as repeatability, low maintenance, and operating over a wide flow range. Here we discuss the meter¡¯s fundamentals, the working principle of thermal mass flow measurement, and the two approaches to measuring heat dissipation.
In-line type accuracy:¡À1.0%
Insertion type accuracy::¡À1.5%
Power supply:DC24V and AC220V
Output:4-20mA,Pulse,RS485

Thermal mass flow meter is precision instruments that can directly measure mass flow,such as industrial gases, compressed gas, and other gases.
Pulse output thermal mass flowmeters are suitable for all industrial and test rig applications that demand quick and precise gas measurement.
Pressure:
Insertion type¡Ü1.6Mpa
Flange type ¡Ü4.0Mpa
Accuracy:
In-line type accuracy:¡À1.0%
Insertion type accuracy::¡À1.5%
Power supply:DC24V and AC220V

Split display insert thermal gas mass flow meter is one kind of competitive gas flow meter for natrual gas industry
Easy installation, simple maintenance, two-way detection, anti-vibration
Flow measurement up to 24 points,and its suitable for low flow measurement ,so thermal gas mass flow meter can be used for leak detection

Thermal flow meter is one kind of gas mass flow meter, can display mass flow rate and total mass flow
According to request, Q&T can do OEM ,such as display converter color,Display LOGO,Flow unit etc.
Output is 4-20mA,Pulse
Communication is RS485 or HART

Thermal gas mass flow meter is one of kind mass flow meter which is popular in industrial.
Q&T gas mass thermal flow meters are be calibrated by gas venturi sonic nozzle calibration device,and ensure the thermal gas mass flowmeter accuracy can reach 1.0% and 1.5%.
Volume flow /Mass flow
SUS304 body
MODBUS RTU RS485
0.1~100Nm/s
4 lines LCD
EX-PROOF

Thermal gas mass flowmeter’s medium temperature range of meter is -40¡æ¡«220¡æ.
When the gas is very humid or saturated with water (e. g. Bio Gas), the piping and flowmeter body should be insulated to prevent water droplets condensing on the measuring sensor.
Insertion type:DN32~DN4000
Flange type:DN10~DN300
Tri-clamp type :DN10~DN100
Thread type:DN10~DN100

Q&T thermal gas mass flow meter can be divided into five sections for correction,this operation will make measuring more accurate
Line type accuracy is ¡À1.0%
Insertion type accuracy is ¡À1.5%
Media:All gas except acetylene and humid gas
Measure range:1:100
Sesnsor working temperature:-20~220℃
Transmitter working temperature:-20~45℃
Output:4-20mA
Accuracy:±1.0%~±2.5%
Probe material:SS316L

LCD display thermal gas flow meter is a meter that uses the principle of heat transfer to detect flow.
The thermal gas flow meter is available in high-performance pipeline type and insert type flow meter. Insert flow meter consist of a probe with sensing elements that are inserted into the pipe irrespective of pipe size. These are easy to install and more economical. Inline flow meters are connected to the pipe itself by the flanged or threaded connection. Inline meters are suitable for smaller diameter pipes.