Products
Position :
Flange Ultrasonic Level Meter
Flange Ultrasonic Level Meter
Flange Ultrasonic Level Meter
Flange Ultrasonic Level Meter

Flange Ultrasonic Level Meter

Level Range: 4,6,8,10,12,15,20,30m
Accuracy: 0.5%-1.0%
Resolution: 3mm or 0.1%
Display: LCD Display
Analog Output: Two Wires 4-20mA/250Ω Load
Introduction
Advantage
Technical Data
Installation
Introduction
Flange ultrasonic level meter  is based on the Time-of-Flight principle. A sensor emits ultrasonic pulses, the surface of the media reflects the signal and the sensor detects it again. The Time-of-Flight of the reflected ultrasonic signal is directly proportional to the distance traveled. With the known tank geometry the level can be calculated.
Advantages
Flange Ultrasonic Level Meter Advantages
Non-contact, maintenance-free measurement.
Measurement unaffected by media properties, like dc value or density.
Calibration without filling or discharging.
Self-cleaning effect due to vibrating sensor diaphragm.
Advantage
Flange ultrasonic level meter application
Flange Ultrasonic level meter with ultrasonic level sensors provides continuous, non-contact and maintenance-free level measurement of fluids, pastes, sludges and powdery to coarse bulk materials. The measurement is unaffected by dielectric constant, density or humidity and also unaffected by build-up due to the self-cleaning effect of the level sensors.
Storage Tank
Storage Tank
Pool
Pool
Drains
Drains
Granary
Granary
Wells
Wells
Metering Box
Metering Box
Technical Data

Table 1: Flange Ultrasonic Level Meter Technical Parameters

Function Compact Type
Level Range 4,6,8,10,12,15,20,30m
Accuracy 0.5%-1.0%
Resolution 3mm or 0.1%
Display LCD Display
Analog Output Two Wires 4-20mA/250Ω Load
Power Supply DC24V
Environmental Temperature Transmitter -20~+60℃ , Sensor -20~+80℃
Communication HART
Protection Class  Transmitter IP65(IP67 Optional),Sensor IP68
Probe Installation Flange, Thread

Table 2: Flange Ultrasonic Level Meter Model Selection

Measure Range
   4   4m
   6   6m
   8   8m
   12  12m
   20  20m
   30  30m
  License
        P  Standard Type(Non ex-proof)
        I   Intrinsically safe (Exia IIC T6 Ga)
     Energy Transducer Material/Process Temperature/Protection Grade
         A  ABS/(-40-75)℃/IP67
         B  PVC/(-40-75)℃/IP67
         C  PTFE/(-40-75)℃/IP67
           Process Connection/Material
             G  Thread
             D  Flange /PP
              Electronic Unit
                 2  4~20mA/24V DC Two Wire
                 3  4 20mA/24V DC /HART Two Wire
                 4  4-20mA/24VDC/RS485 Modbus  Four Wire
                 5  4-20mA/24VDC/Alarm Output  Four Wire
                   Shell / Protection Grade
                     L  Aluminum / IP67
                       Cable Entry
                          N  1/2 NPT
                            Programmer/Display
                                1  With Display
Installation
Flange Ultrasonic Level Meter Installation
1:Keep Ultrasonic Level Transmitter perpendicular to liquid.
2:The transducer should not be mounted too close to the tank wall, the bracket can cause strong false echoes
3:Mount the transducer away from the inlet to avoid false echoes.
4:The transducer should not be mounted too close to the tank wall, the build-up on the tank wall cause false echoes.
5:As is illustrated by the figure on the below, the transducer should be mounted on the top of guide tube to prevent the false echoes from turbulence and foam. The guide tube should come with a vent hole at top of the tube to allow the liquid vapor go out of the tube.
6:When you mount the transducer on the solid tank, the transducer must point to the tank outlet.
 
Send Your Inquiry
Exported to more than 150 countries around the globe, 10000 sets/month production capacity!
Copyright © Q&T Instrument Co., Ltd. All Rights Reserved.
Support: Coverweb