Measuring Pipe Size | DN200-DN3000 |
Connection | Flange |
Liner Material | Neoprene/Polyurethane |
Electrode Marerial | SS316, TI, TA, HB, HC |
Structure Type | Remote Type |
Accuracy | 2.5% |
Output Signal | Modbus RTU, TTL electrical level |
Communication | RS232/RS485 |
Flow speed range | 0.05-10m/s |
Protection Class |
Converter: IP65 Flow Sensor: IP65(standard), IP68(optional) |
Drawing ( DIN Flange )
|
||||||
Diameter (mm) |
Nominal pressure |
L(mm) | H | φA | φK | N-φh |
DN200 | 0.6 | 400 | 494 | 320 | 280 | 8-φ18 |
DN250 | 0.6 | 450 | 561 | 375 | 335 | 12-φ18 |
DN300 | 0.6 | 500 | 623 | 440 | 395 | 12-φ22 |
DN350 | 0.6 | 550 | 671 | 490 | 445 | 12-φ22 |
DN400 | 0.6 | 600 | 708 | 540 | 495 | 16-φ22 |
DN450 | 0.6 | 600 | 778 | 595 | 550 | 16-φ22 |
DN500 | 0.6 | 600 | 828 | 645 | 600 | 20-φ22 |
DN600 | 0.6 | 600 | 934 | 755 | 705 | 20-φ22 |
DN700 | 0.6 | 700 | 1041 | 860 | 810 | 24-φ26 |
DN800 | 0.6 | 800 | 1149 | 975 | 920 | 24-φ30 |
DN900 | 0.6 | 900 | 1249 | 1075 | 1020 | 24-φ30 |
DN1000 | 0.6 | 1000 | 1359 | 1175 | 1120 | 28-φ30 |
QTLD/F | xxx | x | x | x | x | x | x | x | x | x | |
Diameter (mm) | DN200-DN1000 three digit number | ||||||||||
Nominal pressure | 0.6Mpa | A | |||||||||
1.0Mpa | B | ||||||||||
1.6Mpa | C | ||||||||||
The connection method | The flange type | 1 | |||||||||
Liner | neoprene | A | |||||||||
Electrode materials | 316L | A | |||||||||
Hastelloy B | B | ||||||||||
Hastelloy C | C | ||||||||||
titanium | D | ||||||||||
tantalum | E | ||||||||||
Stainless steel coated with tungsten carbide | F | ||||||||||
Structure form | Remote Type | 1 | |||||||||
Remote Type Diving type | 2 | ||||||||||
The power supply | 220VAC 50Hz | E | |||||||||
24VDC | G | ||||||||||
12V | F | ||||||||||
Output/communication | Volume flow 4~20mADC/ pulse | A | |||||||||
Volume flow 4~20mADC/RS232C serial communication interface | B | ||||||||||
Volume flow 4~20mADC/RS485C serial communication interface | C | ||||||||||
Volume flow HART protocol output | D | ||||||||||
Converter form | square | A | |||||||||
Special tag | |||||||||||
lnstall at the lowest point and vertical upward direction
Don't install at the highest point or vertical downward diection |
When drop is more than 5m, install exhaust
valve at the downstream |
lnstall at the lowest point when used in open drain pipe
|
Need 10D of upstream and 5D of downstream
|
Dont' install it at the entrance of pump, install it at the exit of pump
|
lnstall at the rising direction
|